'RELIBIT 1001 Coating'. Factory applied, black coloured bitumen coating. Apply as per manufacturer's Standard Operating Procedure & Guidelines 'RP/291', '203/2024, Revision 1', dated '1st April 2024'. Cure for 10 hours@35°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ZCGJ-2025'. Factory applied, grey coloured Portland Cement Mortar. Mix cement, sand and water in a 2:1:0.4 mass ratio and apply as per manufacturer's instructions issue 'ZC02250725' dated '2025.7.25'. Cure for 12 hours@55°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'ZC-2025HSR'. Factory applied, grey coloured sulphate resistant cement. Mix cement:sand:water in a 1.5:1:0.4 mass ratio and apply as per manufacturer's instructions 'ZC01250725', dated '2025.7.25'. Cure for 8 hours@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Birla SRPC - Electrocement'. Factory applied, grey coloured, cement mortar. Mix cement, sand & water in a mass ratio of 0.6:1.0:0.22 and apply as per manufacturer's Work Instructions 'WP-08-05 I', Issue '04', Revision '0', dated '22.08.2024'. Cure for 24 hours@27°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Hempaline Defend 430'. Factory applied, two-part, white coloured epoxy coating. Mix base and curing agent in a 4:1 volume ratio and apply as per manufacturer's PDS dated 'December 2024'. Cure for 7 days@20°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'8284873 HA002I INT 100 HYF WHITE SN80'. Factory applied, white coloured epoxy coating. Apply as per manufacturer's TDS 'Revision Date: V2, 24.05.2024', 'Region: EMEA'. Cure for 15 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'GF30-NC024'. Light grey coloured, injection moulded, PA66+30%GF material. For use with water up to 85°C.
'LARTON G/40 NAT.:0169F1'. Brown coloured, injection moulded PPS material. For use with water up to 85°C.
'3P764921 Pipe Spacer'. White coloured (opaque), injection moulded PP Pipe Spacer. For use with water up to 85°C.
‘2KPS EX3 Light Pink' & ‘2KPS EX3 Grey'. Site applied, two-part (resin & hardener is automatically mixed in a 3:1 volume ratio through dispensing nozzle) anchor resins. Apply and cure as per ’T Load’ cures set out in Table B4 of European Technical Assessment ‘ETA 16/0884’, dated ‘22/04/2025’. For use with water up to 65°C. If the cure conditions are varied from those specified in ’T Load’ cures set out in set out in Table B3 of European Technical Assessment ‘ETA 16/0884’ then the materials are not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
Page 546 of 652
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
