'Endoprene 888.56'. Factory applied, beige coloured, two-part PU coating. Mix Parts A & B in a 75:25 volume ratio and apply as per Technical Data Sheet dated 09/12/2020. Cure for 8 days@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'181019 Epoxy Phenolic RAL 5012'. Factory applied, blue coloured epoxy phenolic powder coating. Mix and apply as per manufacturer's instructions issued '15.01.2023'. Cure for 10 minutes at 200°C. For use with water up to 55°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Interline 925 Cream'. Site applied, cream coloured, two-component, solvent free epoxy coating. Mix part A (white liquid) with part B (yellow liquid) in a volume ratio of 3:1 and apply as per manufacturer’s TDS ref. ‘2252’ dated 17/12/2020. Cure for 7 days@25°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Eltex TUB124N2025'. Blue coloured, extruded polyethylene material. For use with water up to 23°C.
'Eltex Superstress TUB121N6000'. Black coloured, extruded polyethylene material. For use with water up to 23°C.
'Eltex TUB121'. Black coloured, extruded polyethylene material. For use with water up to 60°C.
'ELTEX Superstress TUB121N3000'. Black coloured, extruded polyethylene material. For use with water up to 23°C.
'Monotape 12, 24 B, 24 BB, 24 HD & 25 BI'. White coloured PTFE tapes manufactured by extrusion, stretching and calendaring. '24 SH, 20SH, 30SH & 28LS-LE'. White coloured PTFE gasket sheets manufactured by extrusion, stretching, sintering and calendaring. For use with water up to 85°C.
'STRONGHOLD SH-EP3'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated '12/11/2020'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘EWA 12150 (EW48) Rev.1. EWA 12155A (EP55) Rev.1. EWA 12160A (EW 60) Rev.1. EWA 12165 (EW65 2GS) Rev.1. EWA 12170 (WRC 70) Rev.1. EWA 12175 (WRC 75) Rev.1. EWA 12180 (EW80) Rev.1’. Black coloured, compression moulded, EPDM sheet materials. Shore hardness between 50 & 80. Tested in-radius size 1.2mm. For use with water up to 85°C.
Page 55 of 247
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
