'VPC5009 Potable FBE'. Factory applied, blue coloured epoxy powder coating. Pre-heat substrate at 200°C and then apply by dipping in a fluidised bed as per manufacturer's instructions dated 10th January 2019. Cure for 15 minutes@200°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5030 Coatings, Paints & Linings

Section Subtitle:

Factory applied pipe & fittings coatings.

WRAS Approval Number:

2312504

Expiry date:

31/12/2028

Approval Holder:

Ferro South Africa (Pty) Ltd.

Company Name

Ferro South Africa (Pty) Ltd.

Address

10 Atomic Street, Vulcania, Brakpan 1540

Country

Republic of South Africa

View All Listings by this Company

'JSGL-OPC (N)'. Factory applied, grey coloured Ordinary Portland Cement. Mix and apply as per manufacturer's work instructions 'JSGL/WI/14', issue '02', revision '00', dated '29.09.2018'. Cure for 4 hours@45°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5030 Coatings, Paints & Linings

Section Subtitle:

Factory applied pipe & fittings coatings.

WRAS Approval Number:

2011555

Expiry date:

30/11/2025

Approval Holder:

Jindal Saw Gulf LLC.

Company Name

Jindal Saw Gulf LLC.

Address

PO Box 92135, Plot No. 11 NR28, ICAD-III, Mussafah, Abu Dhabi

Country

United Arab Emirates

View All Listings by this Company

'LOCTITE GeoSpray Mortar'. Site applied, grey coloured, geopolymer cementitious material. Mix 300g of powder with 60ml water and apply as per manufacturer's instructions 'V: 09.06.2022'. Cure for 96 hours@3°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5042 Coatings, Paints & Linings

Section Subtitle:

Site applied pipe and fittings coatings. Compliance with BS6920 relates to the conditions of cure specified in the listing. If the cure conditions are varied from those described below then compliance with BS6920 cannot be assummed without further testing. Where catalysts are required, only tested catalysts in the recommended concentrations should be used. Manufacturer's advice must be sought if any non standard mixing or curing conditions are being considered.

WRAS Approval Number:

2310509

Expiry date:

31/10/2028

Approval Holder:

Henkel Corporation

Company Name

Henkel Corporation

Address

One Henkel Way, Rocky Hill, 06067

Country

United States

View All Listings by this Company

'15.0903.01 & 15.0902.01'. Dark grey coloured, ferrite anisotropic magnets (commonly known as ceramic magnets). For use with water up to 85°C.

Section:

5165 Magnetic Material

Expiry date:

31/05/2029

Approval Holder:

Eltek SpA

Company Name

Eltek SpA

Address

Strada Valenza 5/A Casale Monferrato

Postcode

15033

Country

Italy

Phone

+39 0142 335511

General Email

f.ruzzafante@eltekgroup.it

View All Listings by this Company

‘Zytel® FG70G30HSR2 BK309’. Black coloured, injection moulded polyamide material. For use with water up to 23°C. From January 2024, the material is for use with water up to 60°C.

Section:

5180 Nylon

Section Subtitle:

Material only. Components made from materials listed in this section may be required to be submitted for audit tests.

WRAS Approval Number:

2308534

Expiry date:

31/08/2028

Approval Holder:

Celanese Sales Germany GmbH

Company Name

Celanese Sales Germany GmbH

Address

Am Unisys Park 1, 65843 Sulzbach am Taunus

Country

Germany

View All Listings by this Company