Range of angled stop valves, (chromium plated brass bodies) with dome operating members. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C
Range of screw down stop valves with plastic bodies for below ground use.. The valves are supplied with loose pipe inserts and are for use with polyethylene pipe (manufactured to BS EN 12201). Maximum working pressure 14.0 bar. Cold water use only.
Range of double regulating valves available with DZR brass, lead free brass or bronze bodies (see models). Products incorporate a non-rising spindle headwork. Products also include two test ports. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of electromagnetic scale inhibitors with stainless steel bodies. Maximum working pressure: 16.0 bar. Cold water use only.
Range of electronic water de-scaler and conditioners with stainless steel bodies. Maximum working pressure 10 bar. Maximum operating temperature 40°C
Electrolytic inline limescale reducer with a zinc plated brass body and a copper coil. Maximum working pressure 10 bar. Maximum operating temperature 80°C.
Range of UV disinfection units with stainless steel bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 35°C.
Range of UV Disinfection units with stainless steel bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of UV disinfection units with stainless steel bodies and quartz tube. Maximum working pressure 8.0 bar. Cold water use only.
Range of inline water meter kits incorporating brass bodies, a spherical valve and drain off valve. For use with copper pipe (manufactured to BS EN 1057:1996). Maximum working pressure 10.0 bar. Cold water use only.
'CELCON F10-52H Blue'. Blue coloured, injection moulded POM material. For use with water up to 40°C.
'CELCON F20-03 BKM'. Black coloured, injection moulded POM material. For use with water up to 85°C.
'CELCON F10-01 T2, F10-02, F10-03H, F20-03M, F25-03 & F30-03M'. The following grades were added to the approval in April 2023: ‘CELCON F30-34, F10-01, F10-03HM, F20-03, F25-03M & F30-03’. Natural, unpigmented (white in appearance), injection moulded POM materials. All the grades listed can be coloured using the following masterbatch CELCON MB-S315F (black coloured masterbatch). All are for use with water up to 85°C.
'CELCON F10-03H BBK & CELCON F10-03H BK'. Black coloured, injection moulded POM materials. For use with water up to 85°C. 'CELCON F10-52H'. Natural (appears white), injection moulded POM material. For use with water up to 40°C.
'TC-7808-19'. Factory applied, grey coloured PTFE coating. Apply as per manufacturer's data sheet dated June 8, 2019. Cure for 20 minutes@380°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotapipe IL 6001-120S'. Factory applied, blue coloured, fusion bonded epoxy powder coating. Pre-heat substrate to be coated for 15 minutes@200°C and coating applied as per manufacturer's TDS dated '22 August 2018'. Post-cure for 15 min@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chosui Coat Grey'. Factory applied, grey coloured (once mixed and applied), two-component epoxy resin coating, Mix base:hardener in a 2:1 weight ratio and apply as per PDS 'CN：IF438122003', dated '03/06/2022'. Cure for 7 days@30°C and then 7 days@60°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Polymer Admixture 850'. Site applied, white coloured liquid primer/sealer. Mix 'Polymer Admixture 850' & water in a volume ratio of 1:1 and apply as per manufacturer’s Product Data Sheet dated Jan 2023. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Supranite 2400'. NBR/fibre gaskets which are white coloured on one side and dark cream coloured on the other, manufactured by calendaring. For use with water up to 23°C. For use only as a jointing/gasket material having been tested at reduced surface area to volume ratio.
'UW TPE HEA-ISO (manufactured from NAKAN HEA 407 EX)'. White coloured (translucent), extruded TPE hose. Shore hardness 66. Tested in-radius size 0.39mm. For use with water up to 65°C.
Page 472 of 567
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
