'ELECTROLINE ES 1212'. Factory applied, white coloured, two-component, solvent -free epoxy coating. Mix base and hardener in a 2:1 volume ratio and apply as per manufacturer's TDS 'ECL/ TDS / ES1212', issue date '2-Feb-14', version '0'. Cure for 7 days@30°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'H-453'. Factory applied, grey coloured ceramic epoxy coating. Apply as per manufacturer's Technical Data Sheet 'TWJ-H-453', 'Edition A1', dated '01/12/2023'. Cure for 7 days@25°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Purethane NXT. Factory applied, off-white coloured, two-component Polyurethane coating. Mix resin and activator in a 2.5:1 volume ratio and apply as per manufacturer's 'APP-CA-NXT-Rev 04', dated '01.04.2023'. Cure for 7 days@23°C. For use with water up to 35°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Deep Seal Liquid Epoxy Paint'. Factory applied, two-component epoxy paint available in red/brown, grey, blue & white colours. Mix base and activator in a volume ratio of 3:1 and apply as per manufacturer's instructions 'DI/FG/2024/056', dated '25/04/2024'. Cure for 7 days@25°C. For use with water up to 65°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Electrocement type CEM III A'. Factory applied, grey coloured slag cement mortar. Mix cement, sand and water in a mass ratio of 0.6:1.0:0.22 and apply as per manufacturer's work instructions 'WP-08-05 I', issue '04', rev. '0', dated '22.08.2024'. Cure for 28 days at 20°C - 22°C OR 24 hours@27°C. For use with water up to 50°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Cicoprime®25 Primer and Cicoshield®PW100 Coating'. Factory applied, grey coloured (once mixed), two-component primer (non-water contact primer) and two-component coating (water contact coating). Mix and apply Cicoprime®25 Primer in a 1:1 ratio and apply as per Technical Data Sheet ‘version 1.1’, dated October 2023. Cure for 2 hours@25°C. Then mix Cicoshield®PW100 Coating in a 1:1 ratio and apply as per Technical Data Sheet ‘version 1.1’, dated August 2024. Cure for 1 minute@25°C. For use with water up to 85°C.
'SMS-FBE-Blue'. Factory applied, blue coloured fusion bonded epoxy coating. Apply as per manufacturer`s TDS 'Document Code 53', 'Publication No 5', dated 01.03.2024. Cure for 35 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘BFSC Foug SDN’. Factory applied, grey coloured, blast furnace slag cement intended to line pipes. Mix sand and cement in a mass ratio of 1.5:1, then add water in a water/cement mass ratio of 0.36:1 and apply as manufacturer's instructions. Cure for 48 hours@23°C, 70% relative humidity. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sikagard® 1816 (formerly known MasterProtect® 1816)'. Site applied, grey coloured (once applied), two-component Epoxy polysulfide coating. Mix parts A & B in a 78:22 weight ratio and apply coat 1 as per manufacturer’s general method statement ‘MS - AD - Sikagard®-1816-01/2024’ and PDS '020303000000002044 Version 01.01', dated April 2024. Cure coat 1 for 9 hours@25°C. Mix parts A & B in a 78:22 weight ratio and apply coat 2 as per manufacturer’s general method statement ‘MS - AD - Sikagard®-1816-01/2024’ and PDS '020303000000002044 Version 01.01', dated April 2024. Cure coat 2 for 14 days@25°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Klingersil C-4430 plus. NBR fibre gasket material, manufactured by calendaring, which is red on one side and beige on the other side. For use with water up to 23°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
Page 444 of 625
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
