‘Rashmi Portland Slag Cement’. Factory applied, grey coloured cement. Mix cement, sand & water in a mass ratio of 1:1.7:0.5 and apply as per manufacturer's instructions 'TSL/TSMD/DI/QA/TPI/DC/003', dated '09/06/2025'. Cure for 4 hours@45°C then cure in open air for 28 days@33-39°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Ramco Ordinary Portland Cement’. Factory applied, grey coloured cement. Mix cement, sand & water in a mass ratio of 1:1.7:0.5 and apply as per manufacturer's instructions 'TSL/TSMD/DI/QA/TPI/DC/001', DATED '09.06.2025'. Cure for 4 hours@45°C then cure in open air for 28 days@33-39°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TML Sagar Sulphate Resisting cement'. Factory applied, grey coloured sulphate resisting cement. Mix cement, sand and water in a mass ratio of 1:1.50:0.50 and apply as per manufacturer's instructions 'TSL/TSMD/DI/QA/TPI/DC/005', dated '09/06/2025'. Cure for 4 hours@28°C. Then 4 hours@45°C. Then 6 hours@40°C (humidity greater than 85%). Then 666 hours@35°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TP1'. Factory applied, colourless solid lubricant. Apply as per manufacturer's instructions 'LDAP-005', issue 1, dated 11/11/2016. For use with water up to 85°C.
'PROTEGOL EP Coating 32-99. Factory applied, two-component, yellow coloured epoxy coating. Mix Component A (resin) with Component B (hardener) in a volume ratio of 1.75:1.0 and apply as per manufacturer's TDS released '03/2025'. Cure for 24 hours at 23°C and then 24 hours at 70°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CB Silicone Lubricant Spray (code: F15215)'. Clear, Silicone Lubricant Spray. Apply as per manufacturer's packaging instructions. For use with water up to 85°C.
'Grivory HT1VA-5 FWA black 9225'. Black coloured, injection moulded nylon material. For use with water up to 85°C.
'ISO Resin Topaz-2100-AT'. Beige coloured polyester resin manufactured by hand layup. For use with water up to 45°C.
'GP Resin Topaz-1110-TP'. Beige coloured polyester resin material manufactured by hand lay-up. For use with water up to 45°C.
'Kuzeyboru HDPE 100 Pipe'. Black coloured, extruded HDPE pipe. For use with water up to 23°C.
'Elofit'. Black coloured, injection moulded, PE100 RC electrofusion & spigot fittings. For use with water up to 85°C.
'Radius Systems PE100 Black Pipe'. Black coloured, extruded PE100 pipe. For use with water up to 23°C.
'TP14371'. Blue coloured polyethylene material manufactured by roto-moulding. For use with water up to 85°C.
'BAILUN PPR Pipe (PPR0411)'. White coloured, extruded PPR pipe. For use with water up to 85°C.
'BAILUN PPR Fittings (PPR051315)'. White coloured, injection moulded PPR fittings. For use with water up to 85°C.
'T MECH PP-RCT pipe'. Green coloured (opaque), extruded PP-RCT pipe. For use with water up to 85°C.
'T MECH PP-RCT Multilayer Pipe'. Extruded, multi-layered pipe comprising of a green coloured (opaque) inner & outer layer and a black coloured (opaque) middle layer. For use with water up to 85°C.
'T MECH PP-RCT fittings'. Green coloured (opaque), injection moulded PP-RCT fittings. For use with water up to 85°C.
'Fluon CD127E'. White coloured, extruded PTFE material. For use with water up to 85°C.
'51M7531 Diaphragm'. Black coloured, calendered, EPDM diaphragm. Shore hardness 75. Tested in-radius size 0.5mm. For use with water up to 85°C.
Page 420 of 522
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
