‘Cicoprime®25 Primer and Cicoshield®PW100 Coating'. Factory applied, grey coloured (once mixed), two-component primer (non-water contact primer) and two-component coating (water contact coating). Mix and apply Cicoprime®25 Primer in a 1:1 ratio and apply as per Technical Data Sheet ‘version 1.1’, dated October 2023. Cure for 2 hours@25°C. Then mix Cicoshield®PW100 Coating in a 1:1 ratio and apply as per Technical Data Sheet ‘version 1.1’, dated August 2024. Cure for 1 minute@25°C. For use with water up to 85°C.
'61300 EPOXY TB BT BLEU 5005'. Factory applied, blue coloured epoxy powder coating. Spray apply as per manufacturers TDS dated '15/2/2019'. Cure for 20 minutes@160°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SMS-FBE-Blue'. Factory applied, blue coloured fusion bonded epoxy coating. Apply as per manufacturer`s TDS 'Document Code 53', 'Publication No 5', dated 01.03.2024. Cure for 35 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ULTRAMID® F3EG10 AQUA SW23285'. Black coloured, injection moulded PA6.1 material. For use with water up to 85°C.
'Veradel AG-330 NT'. Light brown coloured, injection moulded polyethersulfone material. For use with water up to 85°C.
'Veradel AG-320 NT'. Light brown coloured, injection moulded polyethersulfone material. For use with water up to 85°C.
'+GF+ Hakan HDPE PE100 Pipes'. Extruded PE100 pipes which are either blue coloured or black coloured (with blue stripes). For use with water up to 23°C.
'BR-PE-100 Fittings'. Black coloured, injection moulded PE100 fittings. For use with water up to 60°C.
'DELAV HDPE Pipe PE100' and 'DELAV HDPE Pipe PE100-RC'. Black coloured (with blue stripes), extruded PE pipes. For use with water up to 23°C.
'STAR Spigot Fittings'. Black coloured, extruded PE100 fitting. For use with water up to 60°C.
'GY-PEX-b(60-95)'. White coloured (translucent), extruded PEX hose. For use with water up to 85°C.
'Uponor Aqua Pipe'. Extruded, multi-layered PE-X pipe comprising of an off-white inner layer, black middle layer and white outer layer. For use with water up to 70°C.
'GPS Excel Black PE100 Pipe'. Black coloured, extruded PE100 pipe. For use with water up to 23°C.
'Pexylene 50937 Natural, Black & Blue'. Rotationally moulded polyethylene materials available in natural (appears off-white), black & blue colours. For use with water up to 65°C.
'Amodel DW-1140 BK 938 & Amodel DW-1150 BK 938'. Black coloured, injection moulded PPA materials. For use with water up to 85°C.
'+GF+ Hakan Aquasystem Faser Composite Stabil Pipe'. Multi-layered, extruded PPR pipe consisting of a white coloured inner, green coloured middle and white coloured outer layer. The following multi-layered, extruded PPR pipes were added to the approval in April 2025: Green coloured inner, green coloured middle and green coloured outer layer. Beige coloured inner, green coloured middle and beige coloured outer layer. Grey coloured inner, green coloured middle and grey coloured outer layer. For use with water up to 85°C.
'ISOGLASS H8C 4036U NA'. Cream coloured, injection moulded polypropylene material. For use with water up to 85°C.
'Hepworth uPVC Pressure pipe'. Grey coloured, extruded uPVC pipe. For use with water up to 50°C.
'Sylglas Plumber Fix Copper`. Site applied, copper coloured epoxy putty. The putty should be kneaded together, its supplied in a pre-measured 1:1 mass ratio and applied as per manufacturer's directions for use dated August 9th, 2021. Cure for 24 hours@22°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'RAMSET ChemSet 801 Xtrem XC²'. Grey coloured coloured, two-component vinylester resin anchor. Part A is a cream coloured paste and Part B is a dark grey coloured paste, supplied in a pre-weighed cartridge (10:1 volume ratio). Apply as per manufacturer's TDS 'August 15, 2018'. Cure for 24 hours@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 420 of 567
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
