'PROTEGOL EP Coating 32-99. Factory applied, two-component, yellow coloured epoxy coating. Mix Component A (resin) with Component B (hardener) in a volume ratio of 1.75:1.0 and apply as per manufacturer's TDS released '03/2025'. Cure for 24 hours at 23°C and then 24 hours at 70°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5030 Coatings, Paints & Linings

Section Subtitle:

Factory applied pipe & fittings coatings.

WRAS Approval Number:

241055085

Expiry date:

31/10/2029

Approval Holder:

TIB Chemicals AG

Company Name

TIB Chemicals AG

Address

Muhlheimer Strasse 16-22, 68219 Mannheim

Country

Germany

View All Listings by this Company

'Burasil Universal 9544/U'. Green coloured NBR/fibre gasket material manufactured by calandering. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at reduced surface area to volume ratio.

Section:

5075 Fibre

Section Subtitle:

These materials are for use only as a jointing/gasket material having been tested at reduced surface area to volume ratio.

WRAS Approval Number:

250155079

Expiry date:

31/01/2030

Approval Holder:

EagleBurgmann Germany GmbH & Co. KG

Company Name

EagleBurgmann Germany GmbH & Co. KG

Address

Aeussere Sauerlacher Str. 6-10, D-82515 Wolfratshausen

Country

Germany

View All Listings by this Company

‘4TECH 9S20000 W-A ABK’. Black coloured, injection moulded, unfilled PPO/HIPS material. Between February 2024 and April 2025, it was for use with water up to 23°C. Between May 2025 and February 2029, it’s for use with water up to 85°C.

Section:

5250 Polyphenyleneoxide (PPO)

Section Subtitle:

Material only. Components made from materials listed in this section may be required to be submitted for audit tests.

WRAS Approval Number:

240255064

Expiry date:

28/02/2029

Approval Holder:

Safic-Alcan UK Ltd.

Company Name

Safic-Alcan UK Ltd.

Address

812 Fountain Court, Birchwood Boulevard, Warrington

Postcode

WA3 7QZ

View All Listings by this Company

'EP7007PF 'O' ring'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size 0.89mm. For use with water up to 85°C.

Section:

5360 Rubbers

Section Subtitle:

Ethylene Propylene Diene Monomer (EPDM) - components.

WRAS Approval Number:

250655009

Expiry date:

30/06/2030

Approval Holder:

Moken (Xiamen) Industrial Co., Ltd.

Company Name

Moken (Xiamen) Industrial Co., Ltd.

Address

Room 101, No.2, Jixiang West Road, Xinmin Town, Tong'an District, Xiamen City, Fujian Provinces

Country

China

View All Listings by this Company

'EPDM E293'. Black coloured, compression moulded EPDM material. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 85°C.

Section:

5365 Rubbers

Section Subtitle:

Ethylene Propylene Diene Monomer (EPDM) - material only. Components made from materials listed in this section may be required to be submitted for audit tests.

WRAS Approval Number:

250455056

Expiry date:

30/04/2030

Approval Holder:

TRP Sealing Systems Ltd.

Company Name

TRP Sealing Systems Ltd.

Address

24 Netherwood Road, Rotherwas Industrial Estate, Hereford

Postcode

HR2 6JU

View All Listings by this Company

'EPDM2019'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 23°C.

Section:

5365 Rubbers

Section Subtitle:

Ethylene Propylene Diene Monomer (EPDM) - material only. Components made from materials listed in this section may be required to be submitted for audit tests.

WRAS Approval Number:

250455059

Expiry date:

30/04/2030

Approval Holder:

Qingdao Yuanli Sealing Technology Co., Ltd.

Company Name

Qingdao Yuanli Sealing Technology Co., Ltd.

Address

Xinzhuang Industrial Park, Zhuhai Office, Huangdao District, Qingdao City, Shandong Province

Country

China

View All Listings by this Company

Range of hand showers and shower arm kits with (brass bodies - various finishes. The inlets of the hand showers and the inlet elbows incorporate approved check valve cartridges; however, the complete products have not been fully tested to demonstrate they provide backflow protection. Open outlet use only. Maximum operating temperature 65°C.

Section:

1670 Shower Outlets

Section Subtitle:

Shower kit(s)

WRAS Approval Number:

250602017

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

1/2" BSP female (with a ½” BSPP male adaptor for international use) for hand showers. 1/2" NPT male for shower arm.

Marking:

Waterworks logo on handset (BHS010, HNHS010 & CNHS10) Waterworks on escutcheon (BHS010 & BSH001CO)

Installation Requirements:

R001 R040

Expiry date:

30/06/2030

Model:

Hand Showers: BHS010XZZ BHS010ZZ HNHS010ZZ CNHS10ZZ Shower Arm: BSH001XZZ Where XX denotes the finish and can be replaced by: AC = Antique Copper AB = Architectural Bronze AQB = Antique Brass BZ = Architectural Bronze C = Polished Chrome CO = Concordia DN = Dark Nickel G = Gold L = Lumin M = Matte Nickel MC = Matte Chrome MG = Matte Gold MS = Matte Silver N = Polished Nickel S = Silver SC = Shiny Copper SO = Sovereign UB = Unlacquered Brass Where XX denotes the handle components and can be replaced by: 0 = Less Handles 1 = Cross Handle 2 = Two‐Tone Cross Handle 3 = Coin Edge Cross Handle 10 = Solo Series Lever Handle 11 = Lever Handle 12 = Two‐Tone Lever Handle 13 = Coin Edge Lever Handle 14 = Walnut Lever Handle 15 = Leather Lever Handle 20 = Solo Series Straight Lever Handle 2A = Tandem Series Guilloche Lines Lever Handle 2B = Tandem Series Two‐Tone Lever Handle 2C = Union Series Guilloche Link Lever Handle 2D = Union Series Enamel Guilloche Lines Lever Handle 2E = Union Series Guilloche Pinstripe Lever Handle 2P = Solo Series Two‐Piece Straight Lever Handle 2S = Bond Rally Series Lever Handle 2T = Teak Lever Handle 30 = Solo Series Knob Handle 3S = Bond Rally Series Knob Handle 4A = Tandem Series Guilloche Lines Knob Handle 4B = Tandem Series Two‐Tone Guilloche Knob Handle 4D = Union Series Enamel Guilloche Lines Knob Handle 5C = Union Series Guilloche Link Knob Handle 7A = Tandem Series Guiloche Lines Lever handles with Gland Cover 7B = Tandem Series Two Tone Lever handles with Gland Cover 7C = Union Series Guiloche Link Lever handles with Gland Cover 7D = Union Series Enamel Guiloche Lines Lever handles with Gland Cover 7E = Union Series Guiloche Pinstripe Lever handles with Gland Cover 7P = Solo Series Two Piece Straight Lever handle with Gland Cover 7S = Bond Rally Series Lever Handle With Gland Cover 7T = Tandem Series Teak lever with Gland Cover 8Z = Straight Lever Handle 90 = Solo Series Straight Lever handles with Gland Cover

Approval Holder:

Waterworks

Company Name

Waterworks

Address

60 Backus Ave, Danbury, CT 06810

Country

USA

Phone

(203) 546 6140

View All Listings by this Company

Range of wall mounted shower valves (brass bodies – various finishes) incorporating a self-cancelling diverter with a ceramic cartridge headwork controlling flow and temperature and a single lever operating member. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C

Section:

2003 Shower Valves

Section Subtitle:

Shower valve(s) with manual temperature control, incorporating a self-cancelling diverter between outlets.

WRAS Approval Number:

250602018

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

½” BSP F

Marking:

Grohe logo on operating member

Installation Requirements:

R001 R030

Expiry date:

30/06/2030

Model:

24.336.xx1 32.747.xx1 29.079.xx1 001 – Chrome DC1 – Super steel DA1 – Warm sunset AL1 – Brushed hard graphite. GL1 – cool sunrise

Approval Holder:

Grohe AG

Company Name

Grohe AG

Address

Industriepark Edelburg Hemer

Postcode

58675

Country

Germany

Phone

02372 930

General Email

marc.engelhardt@lixil.com

View All Listings by this Company