'ZCGJ-2025'. Factory applied, grey coloured Portland Cement Mortar. Mix cement, sand and water in a 2:1:0.4 mass ratio and apply as per manufacturer's instructions issue 'ZC02250725' dated '2025.7.25'. Cure for 12 hours@55°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.

Section:

5030 Coatings, Paints & Linings

Section Subtitle:

Factory applied pipe & fittings coatings.

WRAS Approval Number:

2205585

Expiry date:

31/05/2027

Approval Holder:

Yingkou Zhuocheng Metal Pipe Fittings Co., Ltd.

Company Name

Yingkou Zhuocheng Metal Pipe Fittings Co., Ltd.

Address

Xianghongqi Village, Jiulongdi Sub-District Office, Gaizhou City, Yingkou City, Liaoning Province

Country

China

View All Listings by this Company

'ZC-2025HSR'. Factory applied, grey coloured sulphate resistant cement. Mix cement:sand:water in a 1.5:1:0.4 mass ratio and apply as per manufacturer's instructions 'ZC01250725', dated '2025.7.25'. Cure for 8 hours@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5030 Coatings, Paints & Linings

Section Subtitle:

Factory applied pipe & fittings coatings.

WRAS Approval Number:

2109569

Expiry date:

30/09/2026

Approval Holder:

Yingkou Zhuocheng Metal Pipe Fittings Co., Ltd.

Company Name

Yingkou Zhuocheng Metal Pipe Fittings Co., Ltd.

Address

Xianghongqi Village, Jiulongdi Sub-District Office, Gaizhou City, Yingkou City, Liaoning Province

Country

China

View All Listings by this Company

'SML-EP012EB'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C. When processing an application for WRAS Product Approval the in-radius tolerance rule cannot be applied, i.e. only the material with an in-radius of 1.0mm is covered by the scope of the approval.

Section:

5365 Rubbers

Section Subtitle:

Ethylene Propylene Diene Monomer (EPDM) - material only. Components made from materials listed in this section may be required to be submitted for audit tests.

WRAS Approval Number:

250755026

Expiry date:

31/07/2030

Approval Holder:

Suzhou Meilong Rubber & Plastic Products Co., Ltd

Company Name

Suzhou Meilong Rubber & Plastic Products Co., Ltd

Address

No.2 Zone 1,WeiBei Industrial Zone, Yudai Road, WeiTang Town, XiangCheng District, SuZhou City, JiangSu Province

Country

China

View All Listings by this Company

Range of bottom entry BS1212-4 (2016) delayed or non delayed action type float operated valves for WC flushing cisterns. Maximum working pressure 10.0 Bar, cold water use only.

Section:

2075 Float Operated Inlet Valve

Section Subtitle:

Can be used to achieve a recognised air gap arrangement, providing it meets the appropriate backflow requirements. Suitable for use in a WC suite, provided it forms an arrangement which meets the requirements of Type AUK1 air gap and an appropriate WC performance specification.

WRAS Approval Number:

251202705

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

½” BSP (M)

Marking:

FLUME on float. BS1212-4 only body.

Installation Requirements:

R001 R550 R560

Expiry date:

31/12/2030

Model:

AB769 Bottom entry inlet valve with G1/2” plastic thread AB769 Bottom entry inlet valve with G1/2” brass thread

Approval Holder:

Toolstation Ltd.

Company Name

Toolstation Ltd.

Address

Travis Perkins PLC Ryehill House Rye Hill Close Lodge Farm Industrial Estate Northampton

Postcode

NN5 7UA

Country

United Kingdom

Phone

07392109053

General Email

benjamin.cockerill@travisperkins.co.uk

View All Listings by this Company

Range of side entry BS1212-4 (2016), delayed action or non-delayed action type float operated valves for WC flushing cisterns. The inlet incorporates an optional flow restrictor. Maximum working pressure 10.0 Bar Maximum operating temperature Cold water use only.

Section:

2075 Float Operated Inlet Valve

Section Subtitle:

Can be used to achieve a recognised air gap arrangement, providing it meets the appropriate backflow requirements. Suitable for use in a WC suite, provided it forms an arrangement which meets the requirements of Type AUK1 air gap and an appropriate WC performance specification.

WRAS Approval Number:

251102003

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Note:

Model can be supplied with either a brass or plastic ½” connection, a plastic 3/8” connection and either delayed or non-delayed action type float valve.

Size:

3/8” BSP (M) 1/2” BSP (M) (brass or plastic inlet connection)

Marking:

FLUME on float. BS1212-4 on body

Installation Requirements:

R001 R550

Expiry date:

30/11/2030

Model:

AB772

Approval Holder:

Toolstation Ltd.

Company Name

Toolstation Ltd.

Address

Travis Perkins PLC Ryehill House Rye Hill Close Lodge Farm Industrial Estate Northampton

Postcode

NN5 7UA

Country

United Kingdom

Phone

07392109053

General Email

benjamin.cockerill@travisperkins.co.uk

View All Listings by this Company