'SSIC/S.S6.S11'. Grey coloured carbon silicon carbide ceramic Ring. manufactured by sintering. For use with water up to 85°C.
‘Pentens SPU-1000 Pure Polyurea Waterproofing Spray Coating (with Pentens E-500SE Primer and Pentens E- 501S Sealer)’. Factory applied, dark yellow coloured (once applied) polyurea primer, sealer & top coat. Mix primer in a 1:1 weight ratio and apply as per PDS v. '2017/02/24'. Cure for 8 hours@25°C. Mix sealer in a 2:1 weight ratio and apply as per PDS v. '2017/02/24'. Cure for 8 hours@25°C. Mix topcoat in a 1.125:1 weight ratio and apply as per PDS v. '2017/02/24'. Cure for 72 hours@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Epilux Solvent Free DW Coating Grey and Red'. Factory applied, light grey or red coloured epoxy coatings. Apply as per manufacturer's data sheet number '558', revision '04', dated October 2022. Cure for 7 days@30°C. For use with water up to 30°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSGL-OPC (N)'. Factory applied, grey coloured Ordinary Portland Cement. Mix and apply as per manufacturer's work instructions 'JSGL/WI/14', issue '02', revision '00', dated '29.09.2018'. Cure for 4 hours@45°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Ascent-01'. Factory applied, grey coloured, Portland cement mortar. Mix sand, cement and water in a weight ratio of 1:1:0.35 and apply as per manufacturer's user instructions 'doc: Ascent-01', 'vision: A08052023', dated '2023-05-08'. Cure for 24 hours@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Eucoflex Caliente'. Site applied, blue coloured, two-component polyurea coating consisting of Component A, Component B and Component C (Pigment Paste). Mix & apply as per manufacturers datasheet 'TX40T815', dated 'August 2023'. For use with water up to 60°C. This approval is valid only for the material when it is applied by experienced, suitably trained applicators that are authorized and/or certified by Euclid Chemical Toxement. The authorization, training and certification of the local applicators are the responsibility of Euclid Chemical Toxement and not the responsibility of WRAS.
'TPU 2053, TPU 2054, TPU 2055, TPU 2056, TPU 2057 & TPU 2058'. Five layered, membrane systems manufactured by calendaring. The membranes consist of: 1.) a transparent polyurethane inner layer (in contact with the water), 2.) a tie layer, 3.) a reinforcing layer (PES or PA), 4.) a tie layer & 5.) a blue or beige coloured polyurethane outer layer (not in contact with the water). For use with water up to 23°C.
'Chesterton Style 455EU'. Blue coloured fibre/NBR material, manufactured by calendaring. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'GRE-FPI-KSA-WAVISTRONG Pipe'. Light brown coloured (opaque), GRE pipe manufactured by helical winding. For use with water up to 85°C.
'GRE-FPI-WAVISTRONG'. Beige coloured GRE pipe manufactured by filament winding. For use with water up to 85°C.
Page 392 of 787
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
