'HP204AD'. Grey coloured carbon bearing, pressed, sintered, impregnated with phenolic resin and rebaked. For use with water up to 85°C.
'Rubalit A 1896'. White coloured, dry-pressed ceramic disc. For use with water up to 85°C.
'JDFF-OPC-01'. Factory applied, grey coloured Ordinary Portland Cement. Mix cement, sand & water in a 1:2:0.50 weight ratio and apply as per manufacturers Work Instruction 'WI-Pc-01-5', 'Issue #: 5 Revision #: 1', dated '10.01.2025'. Cure for 48 hours@23°C. For use with water up to 85°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
EUROKOTE® 711.92BF bleu 5012, EUROKOTE® 711.92BF bleu 5015, EUROKOTE® 711.92BF bleu 5005 CR, EUROKOTE® 711.92BF bleu 5005 & EUROKOTE® 711.92BF bleu 5017. EUROKOTE® 711.92BF noir 9005. EUROKOTE® 711.92 bleu 5012, EUROKOTE® 711.92 bleu 5015, EUROKOTE® 711.92 bleu 5005, EUROKOTE® 711.92 bleu 5005 CR & EUROKOTE® 711.92 bleu 5017. EUROKOTE® 711.92 noir 9005. EUROKOTE® 711.92 BF Brun Rouge & 711.92 Brun Rouge Factory applied, blue, black or red coloured epoxy coatings. Apply as per manufacturer's technical data sheets dated 04/03/2025. Cure for 2 minutes@200°C. For use with water up to 85°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'AL 83275'. Factory applied, blue coloured enamel coating. Apply as per manufacturer's TDS 'TDS-2025-AL83275-REV00', dated '03.07.2025'. Cure for 7 minutes@860°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TESNIT® BA-KTW-G'. Off-white coloured NBR/fibre gasket material manufactured by calendaring. For use with water up to 85°C.
'EPP-GRE Pipe'. Translucent, green coloured GRE pipe (with epoxy resin), manufactured by filament winding. For use with water up to 85°C.
'Molykote® G-5511'. White coloured (opaque), silicone based grease. Apply as per manufacturer's instructions. For use with water up to 85°C.
'ICMA PE-RT TYPE II/AL/PE-RT TYPE II Multilayer Pipe'. Extruded, multi-layered pipe comprising of a white coloured PE-RT TYPE II inner and outer layer and aluminium middle layer. For use with water up to 85°C.
'Salman Plastic IpekBoru HDPE Pipe'. Blue coloured, extruded HDPE pipe. For use with water up to 85°C.
'PE-UltraFLO Pipe'. Black coloured, extruded HDPE pipes. For use with water up to 85°C.
'Plastazote HD30 to HD110'. Extruded, HDPE foams available in natural (appears white) or black (appears dark grey). 'Evazote EV30 to EV50'. Extruded, EVA foams available in natural (appears white) or black (appears dark grey). 'Plastazote LD70’. Extruded, LDPE foams available in natural (appears white coloured) or black. For use with water up to 85°C. 'Plastazote LD15 to LD60’. Extruded, LDPE foams available in natural (appears white coloured) or black. For use with water up to 50°C.
'Plate PE 100 natur'. White coloured (translucent), extruded, polyethylene 'support' component. For use with water up to 85°C.
'Polypipe MecFlow Pipes'. Triple layered, extruded PPR pipe consisting of a white coloured inner, black coloured middle and grey coloured (with white stripe) outer layer. For use with water up to 85°C.
'Polypipe MecFlow Fittings'. Grey coloured, injection moulded PPR fittings. For use with water up to 85°C.
'Advance Plastics PPR Pipe'. Green coloured (with red stripe), extruded PPR pipe. For use with water up to 85°C.
'Locking Pin NGAB-00707'. Off-white coloured (translucent), extruded polypropylene pipe. For use with water up to 85°C.
‘RIALENE P 100 SGFxx KTW grau K 7-128, RIALENE P 100 SGFxx KTW weiß K 9-112, RIALENE P 100 SGFxx KTW schwarz’. Injection moulded polypropylene materials available in grey, white and black. The ‘xx’ in the material name can be replaced with any number between ‘10’ and ‘50’. For use with water up to 85°C.
‘JCP HIGH Load Vinylester JFV380SF & JFV300SF’. Site applied, grey coloured, two-part (resin & hardener is automatically mixed in a 10:1 volume ratio through dispensing nozzle) anchor resin. Apply and cure as per ’T Load’ cures set out in Table B3 of European Technical Assessment ‘ETA 15/0704’, dated ‘31/01/2023’. For use with water up to 23°C. If the cure conditions are varied from those specified in ’T Load’ cures set out in set out in Table B3 of European Technical Assessment ‘ETA 15/0704’ then the material is not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
'B8066'. Black coloured, compression moulded Chlorobutyl rubber material. Shore hardness 50. Tested in-radius size 1.05mm. For use with water up to 85°C.
Page 367 of 393
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
