'Chemfix 100'. Site applied, grey coloured chemical anchor resin. Apply as per manufacturer's instructions ref. no. 'rev5' dated 04/06/218. Cure for 48 hours@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'vinyl eco/EASF'. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resin. Apply as per manufacturer's instructions dated 25/09/2017. Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CH200'. Brown coloured chemical anchor resin. Apply as per manufacturer's instructions 'version 24/05/2018'. Cure for 24 hours@5°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
'Chemfix CH+ MAX'. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resin. Apply as per manufacturer's instructions dated 18/05/2022. Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EPDM 70.502-03 washers & 'O' rings'. Black coloured, injection moulded EPDM washers and 'O' rings. Shore hardness 70. Tested in-radii sizes between 0.5 and 2.6mm. For use with water up to 85°C.
`SW EPDM`. Black coloured, extruded, EPDM hose. Shore hardness 85. Tested in-radii sizes between 0.75mm & 1.70mm. For use with water up to 85°C.
'E24 EPDM moulded parts.' Black coloured, injection moulded EPDM seals. Shore hardness 75. Type 1 moulded seals have a tested in-radius size of 4.2mm and Type 2 moulded seals have a tested in-radius size of 0.7mm. For use with water up to 85°C.
'01/U70EP 'O' ring' with a tested in-radius size between 0.5mm & 3.5mm. In June 2024, the follow components were added to the approval: ‘01/U70EP Cylindrical Gasket’ with a tested in-radius size between 0.9mm & 1.25mm. ‘01/U70EP Membrane’ with a tested in-radius size between 2.1mm & 5.5mm. Black coloured, injection moulded EPDM components. Shore hardness 70 For use with water up to 85°C.
'AquaFlex T 5857'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 70°C.
‘ME0996’ components. Black coloured, injection moulded NBR rubber components. ‘O’-rings with an in-radius size of between 0.5mm & 5.0mm. Shore hardness between 40 & 90. Between November 2023 and April 2024, the approval included gaskets with an in-radius size of 5.0mm. Shore hardness 40. From May 2024 the gasket range was extended to include gaskets with an in-radius size of between 0.5mm & 5.0mm. Shore hardness between 40 & 90. For use with water up to 23°C.
'NB7041F'. Black coloured, compression moulded NBR material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 65°C.
'Griffon UNI-100 XT'. Amber coloured solvent cement intended to join PVC pipe and fittings. Apply as per manufacturer's instructions '6300427', issue '1'. Cure for 24 hours@7°C. For use with water up to 35°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Paryls® PPSU F1550NC (natural grade – appears brown), F1550GY (grey coloured), F1550BK (black coloured) & F1550WH (white coloured)’. Injection moulded PPSU materials. For use with water up to 85°C.
Range of screw down stop valves with plastic bodies incorporating EPDM ‘O’-rings and seal. For use with PE-X pipe (manufactured to BS7291-3), BPB pipe (manufactured to BS7291-2) and copper pipe (manufactured to EN1057). Maximum working pressure and operating temperatures: 12.5 bar @ 20°C & 6.0 bar @ 65°C.
Bidet seat assembly which discharges via a sensor actuated solenoid valve and utilises a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). The inlet incorporates a strainer and flow regulator. Maximum working pressure 10.0 bar. Cold water supply only.
Range of wall mounted, single hole, single outlet, fixed, electronically controlled tap assemblies (chrome plated brass bodies). Flow is controlled via an infra-red activated solenoid valve and the spout outlets incorporate a plastic aerator. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (fixed) electronically controlled tap assemblies in (chrome plated brass bodies). Flow is controlled with a solenoid valve activated via an infra-red sensor. The temperature is controlled via a single lever operating member on the body. The inlets incorporate stainless steel strainers and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlets incorporate a plastic aerator. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet, fixed, electronically controlled combination tap assemblies, (chrome plated brass bodies). Flow is controlled via an infra-red activated solenoid valve and the spout outlets incorporate plastic aerators. A stainless steel braided PEX lined flexible hose connects the components. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 45°C
Single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The spout outlets incorporate a plastic aerator and flow regulator. The tap incorporates a soap dispenser with separate dispensing nozzle. Maximum working pressure 8.0 Bar. Maximum operating temperature 55°C.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (stainless steel or brass bodies – various finishes). Flow is controlled via solenoid valve (housed in a control box) actuated via an infra-red sensor, the inlets to the control box incorporate stainless steel strainers. The spout outlets incorporates plastic aerators. The products incorporate a stainless steel PEX lined flexible hose assembly, connecting the tap to the solenoid valve. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Page 365 of 555
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
