'(UREFLEX) TM390'. Off-white coloured, injection moulded PUR material manufactured by casting. For use with water up to 23°C.
'S-9028'. Black coloured, compression moulded EPDM rubber material Shore hardness 60 ShA. Tested in-radius size 1.0mm. For use with water up to 60°C.
'EBW-65'. Black coloured, compression moulded EPDM rubber material. Shore hardness 65. Tested in-radius size 0.98mm. For use with water up to 85°C.
'RCI EP 70'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 0.95mm. For use with water up to 65°C.
'EPDM BW 5920 D 50'. Black coloured, compression moulded EPDM material. Shore hardness 50. Tested in-radius size 1.0mm. For use with water up to 70°C.
'ILPEA 70-90 EPDM COMPOUND WRAS AF'. Black coloured, compression moulded EPDM material. Shore hardness 80. Tested in-radius size 1.25mm. For use with water up to 23°C.
'Sunaflex T 8289'. Black coloured, compression moulded EPDM rubber material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 23°C.
'LC 50-90'. Black coloured, compression moulded EPDM rubber material. Shore hardness 70. Tested in-radius size 1.33mm. For use with water up to 85°C.
'Viton `A` V99 gaskets'. Black coloured gaskets cut from calendered fluoroelastomeric material. Shore hardness 70. Tested in-radius size 1.5mm. For use with water up to 23°C.
'006800.3 washer, 006802.6 washer & 006906.4 slab (made using 7741 compound)'. Red coloured, compression moulded VMQ components. Shore hardness 70. The '006800.3 washer’ has a tested in-radius size of 1.16mm. The ‘006802.6 washer’ has a tested in-radius size of 1.15mm. The ‘006906.4 slab' has a tested in-radius size of 1.17mm. For use with water up 85°C.
'Silicone LSR2090-50'. Colourless (translucent), injection moulded silicone rubber material. Shore hardness 50. Tested in-radius size between 0.25mm & 3.5mm. For use with water up to 85°C.
'Loctite EA 9480'. Site applied, two-component, white coloured (once mixed) epoxy adhesive. Mix and apply as per manufacturer's technical data sheet dated October 2014. Cure for 7 days@22°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Novodur® SBM-90 Q203'. Natural (appears off-white), injection moulded thermoplastic resin. The natural material may be coloured using the following INEOS Styrolution colourants at the agreed maximum percentage concentrations by weight: Pigment White 6, Black 7, Blue 15:3, Blue 29, Brown 24, Red 101, Violet 15, Green 7, Green 17 & Yellow 53. For use with water up to 60°C.
'Novodur® SBM-90'. Natural (appears off-white), injection moulded thermoplastic resin. The natural material may be coloured using the following INEOS Styrolution colourants at the agreed maximum percentage concentrations by weight: Pigment White 6, Black 7, Blue 15:3, Blue 29, Brown 24, Red 101, Violet 15, Green 7, Green 17 & Yellow 53. For use with water up to 60°C.
A range of wall mounted two hole single outlet (fixed) electronically controlled tap assemblies with brass bodies (various finishes). Flow is controlled by a solenoid valve activated by via an infra-red sensor on the underside of the tap. The inlets of the function block incorporate stainless steel strainers, plastic silencers and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum working temperature 60°C.
Deck mounted, single hole, single outlet (fixed) electronically controlled tap assembly (various finishes). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Product supplied with metal backnuts. Maximum working pressure 6.0 bar. Maximum operating temperature 40°C.
WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of check valve cartridges with plastic bodies to be housed in specifically dimensioned bodies. The product incorporates a plastic flow regulator. Maximum working pressure 16.0 bar & maximum operating temperature 65°C.
Range of non-verifiable double check valve assemblies (DZR brass bodies) incorporating spherical valves and either red or blue butterfly handles. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of double check valve assemblies consisting of two spring loaded resilient trim in-line check valve cartridges housed in a DZR brass body (chrome plated or brass finish) with a port located between the cartridges. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Page 37 of 214
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
