'GIX96W-BR & GIX99.7W-BR'. Cream coloured ceramic bearing rings manufactured by pressing, sintering & re-working. For use with water up to 85°C.
'ET-52184 & ET-52185'. Factory applied, black coloured water-based silicone coating comprising of an under-coat (ET-52184) and finishing coat (ET-52185). Apply as per manufacturer's instructions 'V8.2' issued January 2019. Cure both undercoat and finishing coat for 10 minutes@25°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ELM EPX 13'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's instructions to end users reference no. 'ELM/2019/10/001' dated '23/08/2024'. Cure for 10 minutes@130°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Polyflon PTFE TC-7808-19 Grey PTFE Coating'. Factory applied, grey coloured PTFE coating. Apply as per manufacturer's technical data sheet dated 'June 8, 2012'. Cure for 20 minutes@380°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TML Dalmia Sulphate Resisting cement'. Factory applied, grey coloured sulphate resisting cement. Mix cement, sand and water in a mass ratio of 1:1.50:0.50 and apply as per manufacturer's instructions 'TSL/TSMD/DI/QA/TPI/DC/004', dated '09/06/2025'. Cure for 4 hours@28°C. Then 4 hours@45°C. Then 6 hours@40°C (humidity greater than 85%). Then 666 hours@35°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ZX-9 Fusion Bonded Epoxy Powder Coating Blue & Red'. Factory applied, blue or red coloured epoxy coatings. Apply as per manufacturer's TDS 'ZX-9-HX' dated '2025.4.25'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'VETOPROOF EC720'. Site applied, grey coloured, two-part epoxy coating. Mix parts A and B in a 84.8:15.2 weight ratio and apply three coats as per manufacturer's Method Statement 'MoS-SA-G1104-M-AK-09-23', dated '18 September 2023'. Cure first coat for 24 hours at 23°C, second coat for 24 hours at 23°C and third coat for 7 days at 23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'VETOPROOF EC722'. Site applied, grey coloured, two-part epoxy coating. Mix parts A and B in a 85.4:14.6 weight ratio and apply three coats as per manufacturer's Method Statement 'MoS-SA-G1101-M-AK-09-23', dated '18 September 2023'. Cure first coat for 24 hours at 23°C, second coat for 24 hours at 23°C and third coat for 7 days at 23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Fortron ICE 504L SD 3039 black (DW)'. Black coloured, injection moulded PPS material. For use with water up to 85°C.
'Lubricomp CX94108-GYDKNAT'. Dark grey coloured, injection moulded Polystyrene material. For use with water up to 85°C.
Page 339 of 445
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
