'SRC RZ S&M&BDN 20'. Factory applied, grey coloured sulphate resistant cement mortar. Mix cement and sand in a 1:2.2 mass ratio. Combine that mix and water in a 1:0.45 mass ratio. Cure for 24 hours@25°C and 95% relative humidity. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EP01'. Factory applied, blue coloured epoxy powder coating. Apply and cure as per manufacturer's instructions 'V6.3' issued March 2019. For use with water up to 65°C.
'V-PET #1600 Gray F'. Factory applied, grey coloured epoxy resin powder coating. Apply as per manufacturer`s instructions ref. no. '20210216-1' dated 2021/2/16. Cure for 10 minutes@200°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Promag’. Factory applied coating system, black coloured, consisting of two component primer and three component polyurethane top coat. Mix primer in a ratio 2:1 by weight (component A:B), apply and cure for 2 hours at 23°C, then mix topcoat in a ratio 100:5.6:2.4 by weight (component A:B:C) before applying and curing for 20 seconds at 23°C. This approval covers the following manufacturing sites: France and China. For use with water up to 23°C.
'EP-621'. Factory applied, blue coloured epoxy powder coating. Apply and cure as per manufacturer's instructions file no: 'TJR-QM-CO-032', 'edition A1' dated '2021-Feb.-26th'. For use with water up to 65°C.
'HEMPADUR 35600 Cream and Red'. Factory applied, cream or red coloured (when mixed), two-component epoxy coatings consisting of a base and curing agent. Mix the base and curing agent in a 14.8:5.2 volume ratio. Cure for 8 days@25°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Balinit DLC-Star.' Factory applied, grey coloured CrN + a-C:H coating. Apply as per manufacturer's instructions reference 'VS200295' dated 18.03.2021. Cure for 6 hours@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`BFSC MAS S&MDN 20`. Factory applied, grey coloured, blast furnace slag cement mortar. Mix sand and cement in a mass ratio of 2.35:1. Add water to give a mass ratio of 1:0.45 (cement:water). Cure first time for 7 hours@70°C. Cure second time for 12 hours@70°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Flogul® 645 Bleu 5005 (blue coloured) & Flogul® 645 Noir (black coloured)'. Factory applied, PVDC coatings to be applied in accordance with manufacturer's data sheet dated '11/09/2018'. Cure for 7 days@20°C. Flogul® 645 Bleu 5005 is for use with water up to 23°C. Flogul® 645 Noir is for use with water up to 60°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'RUNBAO Epoxy resin coating 5017' (light blue), 'RUNBAO Epoxy resin coating 5005' (blue) & 'RUNBAO Epoxy resin coating 3016' (red). Factory applied electro-statically sprayed epoxy resin coating. Apply and cure as per manufacturer's instructions version 'YZRB-2015V1.0' dated '2015-06-01'. Between January 2021 and 9th December 2021, the materials were suitable for use with water up to 23°C. Between 10th December 2021 and 31st January 2026, the materials are suitable for use with water up to 85°C.
'YHCM-01'. Factory applied, grey coloured sulphate resisting cementitious mortar. Mix sand, cement & water in a ratio of 1: 2.5: 0.3. Cure for 4 hours@20°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'OCPOL 611'. Beige coloured (translucent), Isophthalic Unsaturated Polyester Resin with glass fibre material manufactured using hand-lay method. For use with water up to 70°C.
'ResinTech CG10-F-UPS'. Gold coloured ion exchange resin. For use with water up to 65°C.
'Krytox™ Oils; GPL 104, 143AB, VPF 1525, VPF 1531, AUT 1045, GPL 105, GPL 106, 143AC, 143AD & GPL 107'. Clear (colourless), perfluoropolyether oils. 'Krytox™ Greases; GPL 204, 240AB, AUT 2045, GPL 205, GPL 206, 240AC, 240AD & GPL 207'. White coloured, Polytetrafluoroethylene thickened perfluoropolyether greases. All are suitable for use with water up to 85°C.
'RP380s & RP361'. Off-white coloured (opaque) silicone greases. Apply as per manufacturer's instructions. For use with water up to 65°C.
'Badamid B70 GF40 UV WL Black'. Black coloured, injection moulded, glass filled PA6 material. For use with water up to 65°C.
'PA66+50%GF 1620G50 BK015'. Black coloured, injection moulded PA66 (with 50% glass fibre) material. For use with water up to 85°C.
Grivory GV-2H natural & GV-2H black 9915. GV-2 FWA natural & GV-2 FWA black 9225. GV-4H natural & GV-4H black 9915. GV-4 FWA natural & GV-4 FWA black 9225. GV-5H natural & GV-5H black 9915. GV-5 FWA natural, GV-5 FWA black 9225 & Grivory XE 4275 black 9225. GV-6H natural & GV-6H black 9915. GV-6 FWA natural & GV-6 FWA black 9225. Injection moulded, natural (appears white) or black coloured, glass reinforced nylon materials. For use with water up to 23°C.
‘ELGEF PE-100 electrofusion fittings’, Black coloured, injection moulded polyethylene electrofusion fittings. For use with water up to 65°C.
'MMP PE100 Pipe'. Black coloured (with blue coloured external stripes), extruded PE100 pipes manufactured from 'Sabic P6006' or 'Borouge HE3490-LS'. For use with water up to 85°C.
Page 33 of 427
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
