'ITK-STE 221 (cream coloured), ITK-AL 99 (cream coloured) & ITK-AL96 (white coloured)'. Compression moulded and sintered ceramic sealing rings. For use with water up to 85°C.
'CP231200'. Factory applied, two-part water-based epoxy coating. Mix Parts A & B in a 5:1 weight ratio and apply as per manufacturer's instructions 'File No. HBB-01', 'Version: A', dated '2024.6.30'. Cure for 24 hours@26°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TOHPEPOWDER#6150 SHK GRAY QD'. Factory applied, grey coloured epoxy coating. Apply as per Tohpe Corporation instructions no '4230904550B'. dated 'Jan 28, 2025'. Cure for 5 minutes@200°C. For use with water up to 65°C.
'JSGL-BFSC III A (S)'. Factory applied, grey coloured cement mortar. Mix cement:sand:water in a 1:1.7:0.5 weight ratio and apply as per manufacturer's work instructions 'JSGL/WI/14', 'Issue No. 02', 'Revision No. 00', dated '29.09.2018'. Cure for 4 hours@45°C (R.H. 85%). For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSGL-BFSC III B (S)'. Factory applied, grey coloured cement mortar. Mix cement:sand:water in a 1:1.7:0.5 weight ratio and apply as per manufacturer's work instructions 'JSGL/WI/14', 'Issue No. 02', 'Revision No. 00', dated '29.09.2018'. Cure for 4 hours at 45°C (R.H. 85%). For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSGL-BFSC (E)'. Factory applied, grey coloured cement mortar. Mix cement:sand:water in a 1:1.7:0.5 weight ratio and apply as per manufacturer's work instructions 'JSGL/WI/14', 'Issue No. 02', 'Revision No. 00', dated '29.09.2018'. Cure for 4 hours at 45°C (R.H. 85%). For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSGL-SRC (E)'. Factory applied, grey coloured cement mortar. Mix cement:sand:water in a 1:1.7:0.5 weight ratio and apply as per manufacturer's work instructions 'JSGL/WI/14', 'Issue No. 02', 'Revision No. 00', dated '29.09.2018'. Cure for 4 hours@45°C (R.H. 85%). For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Pulron 101 Aqua'. Factory applied, blue coloured PE coating. Apply as per manufacturer's instructions application guide dated 07.02.2018. Cure for 10 minutes@200°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW– JAL (OPC-TICL)'. Factory applied, grey coloured Ordinary Portland Cement. Mix sand, cement & water in a 1.5:1.0:0.5 weight ratio and apply as per manufacturer's instructions 'JSL/QA/PR-06', version '2.0', dated '15.02.20'. Cure for 27 days@21°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL (SRPC-DCL)'. Factory applied, grey coloured Sulphate resistant Portland Cement. Mix sand, cement & water in a 1.5:1.0:0.5 weight ratio and apply as per manufacturer's instructions 'JSL/QA/PR-06', version '2.0', dated '15.02.20'. Cure for 27 days@21°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL (BFSC-JSL)'. Factory applied, grey coloured Blast furnace slag cement. Mix sand, cement & water in a 1.5:1.0:0.5 weight ratio and apply as per manufacturer's instructions 'JSL/QA/PR-06', version '2.0', dated '15.02.20' and apply as per. Cure for 27 days@21°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Electrocement CEM I-SR3 – Parasakti SRPC)'. Factory applied, grey coloured, Sulphate Resisting Portland Cement. Mix cement, sand & water in a 0.6 : 1.0 : 0.22 mass ratio and apply as per work instructions 'WP-08-05 I', issue '04', rev. '0' dated '22.08.2024. Cure for 24 hours@27°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Nylon 11'. Factory applied nylon coatings available in white or grey colours. The substrate the coating is to be applied to is heated to 310°C for 30 minutes and the coating applied as per manufacturer's work instructions 'WI-09-19 Rev. 6' dated April 22, 2020. Cure for 10 minutes@270°C. The white coating is for use with water up to 23°C. The grey coating is for use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'POLYGEL-2136'. Factory applied, two-part, white coloured (opaque) isophthalic gelcoat comprising of a resin and catalyst. Mix resin and catalyst in a 50:1 mass ratio and apply as per manufacturer's TDS 'Revision No. 10', dated 'SEPT 2024'. Cure for 3 hours@85°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jindal Saw Limited Ordinary Portland Cement - 53 Grade'. Factory applied, grey coloured Ordinary Portland Cement. Mix cement, sand & water in a xx ratio of 1:1.5:0.5 and apply as per manufacturer's Work Instructions 'JSAW/AP01/DISP/PRO/WI-09', version '2.0', effective date '01.05.2023'. Cure for 2.5 hours@48°C and then 3 days@30°C. For use with water up to 60°C.
'LM-coat'. Factory applied, blue coloured, two-part Polyurea coating. Mix Part A (KOBECASE PS-6031) with Part B (COBENATE I-362) in a 100:100 volume ratio and apply as per manufacturer's TDS 'Rev. no: 02', dated '16.02.2022'. Cure for 4 hours@10°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SikaTop®-107 Seal AE'. Site applied, grey coloured, two-part coating. Mix parts A and B in a 1.4 weight ratio and apply as per manufacturer's Method Statement 'V1', dated 'Feb 2025'. Cure Coat 1 for 3 hours at 30°C. Cure Coat 2 for 21 days at 30°C. Between January 2025 and December 2025, the coating is for use with water up to 23°C. Between January 2026 and January 2030, the coating is for use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NATCEM AC'. Site applied, grey coloured cement mortar. Mix 'NATCEM AC' and water in a weight ratio of 5:1 and apply as per manufacturer's Instructions for Use 'Issue 4', dated '16 September 2024'. Cure for 4 hours@0°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Hansung M&S GRP Panel'. Light grey coloured, hot press moulded GRP panel. For use with water up to 60°C.
'UNISILKON TK 002/1000'. Clear lubricant, to be applied as per manufacturer's instructions. For use with water up to 65°C.
Page 320 of 443
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
