Circulation pump with a stainless steel body. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

241104706

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

1½” BSP (M)

Marking:

Archergas, model and technical information on case. Flow arrow on body.

Installation Requirements:

R001

Expiry date:

30/11/2029

Model:

DHW15 Circulation Pump.

Product Images

Approval Holder:

Archergas Limited

Company Name

Archergas Limited

Address

85 Bayham Street, Camden Town

View All Listings by this Company

Range of booster sets, incorporating a stainless-steel manifold system and between 2 and 5 pumps depending on model. The booster sets also incorporate spherical valves, non-return valves, pressure switches/sensors and expansion vessels. Maximum working pressure 16.0 Bar. Maximum operating temperature 25.0°C.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

241202019

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

DN 50 to DN 200

Marking:

Armstrong and product info on adhesive label on pump.

Installation Requirements:

R001 R415

Expiry date:

31/12/2029

Model:

6800 DE 2-3 Pump VMS 4 2-3 Pump VMS 6 2-5 Pump VMS 10 2-5 Pump VMS 15 2-5 Pump VMS 25 2-4 Pump VMS 40 2-4 Pump VMS 60

Product Images

Manufacturer:

Armstrong Fluid Technology

Company Name

Armstrong Fluid Technology

Address

1 Woverton Street Manchester M11 2ET

Postcode

M11 2ET

Country

United Kingdom

View All Listings by this Company

Range of shower booster pumps with brass bodies and plastic impellers. The body incorporates a single check valve cartridge, however the complete assembly has not been tested to demonstrate it provides adequate backflow protection. Maximum working pressure: 4.0 bar. Maximum operating temperature: 70°C.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

250304701

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

½” BSP (F).

Marking:

Flowflex, flow arrow and BS6282-5 on body.

Installation Requirements:

R001

Expiry date:

31/03/2030

Model:

SP2B, SP1 (same as SP2B without electronics), SP22S (2 x SP2B connected electronically), SP21S (1 x SP2B & 1 x SP1 connected electrconically), SP2U (SP2B without transformer), SP1U (SP1 without transformer).

Approval Holder:

Flowflex Components Ltd.

Company Name

Flowflex Components Ltd.

Address

Samuel Blaser Works Dew Pond Lane Tongue Lane Industrial Estate Buxton

Postcode

SK17 7LR

Country

United Kingdom

Phone

+44 1298 77211 Fax: 01298 72362 Telex: 666482

General Email

daniel.jones@fowflex.com

View All Listings by this Company

‘UPM10’ and ‘UPM20’ range of circulator pumps with a stainless-steel body, plastic impellor and EPDM ‘O’-rings. The product is supplied with EPDM gaskets for the inlet and outlet. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

241207701

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

1½” BSP (M) inlet/outlet.

Marking:

Grundfos and Grundfos logo, type and model on nameplate on motor housing. P/N no., P/C no., Serial (S/N) no., technical info, manufacturing country and data matrix on end of motor housing. Flow arrow on body.

Installation Requirements:

R001

Expiry date:

31/12/2029

Model:

UPM 10M 25-95 N 180, UPM 10L 25-105 N 180, UPM 10XL 25-125 N 180, UPM 20S 25-145 N 180. Where: Pump type: UPM 10M, UPM 10L, UPM 10XL, UPM 20S. Control variant: []: PWM, LIN: LIN bus input signal, 0-10V, AUTO, HYBRID, SOLAR, DHW. Nominal diameter: 25: G 1½”. Max. Head: 95: 9.5m, 105: 10.5m, 125: 12.5m, 145: 14.5m. Designation/Pump housing: N 180: Stainless steel body, 180mm port to port length. Control box orientation: 3: 3 o’clock (right), 6: 6 o’clock (below), 9: 9 o’clock (left). Customer code: XXX (no impact on water contact parts).

Product Images

Approval Holder:

Grundfos Holding A/S

Company Name

Grundfos Holding A/S

Address

Poul Due Jensens Vej 7 Bjerringbro

Postcode

DK-8850

Country

Denmark

Phone

+36302482216

General Email

oszilagyi@grundfos.com

View All Listings by this Company

'HYDRO MULTI-E' booster set range consisting of two to four electronically controlled pumps connected in parallel and mounted on a common base frame provided with all necessary fittings. The suction manifold incorporates an isolation valve fitted between it and the individual pumps, and a pressure switch with an isolation valve. The discharge manifold incorporates an isolation valve and a non-return valve (not suitable for backflow protection), which is fitted between it and the individual pumps, it also incorporates a combined isolation and drain valve. Maximum working pressure 16.0 bar. Cold water use only.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

250107701

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

2” or 2½” BSPT (M). DN80 or DN100 flanged.

Marking:

Grundfos and Grundfos logo on pumps. Grundfos and Grundfos logo, type, Model, P/N no., Serial no., technical info, manufacturing country on adhesive label on pump base plate.

Installation Requirements:

R001 R415 R511

Expiry date:

31/01/2030

Model:

2” or 2½” BSPT (M): HYDRO MULTI-E “X” CRIE1-* x1 x2-x3-x4-x5-x6. HYDRO MULTI-E “X” CRIE3-* x1 x2-x3-x4-x5-x6. HYDRO MULTI-E “X” CRIE5-* x1 x2-x3-x4-x5-x6. 2½” BSPT (M) or DN80 flanged. HYDRO MULTI-E “X” CRIE10-* x1 x2-x3-x4-x5-x6. DN80 or DN100 flanged. HYDRO MULTI-E “X” CRIE15-* x1 x2-x3-x4-x5-x6. HYDRO MULTI-E “X” CRIE20-* x1 x2-x3-x4-x5-x6. The “X” preceding CR indicates the number of pumps in the booster set, between 2 and 4 pumps. CRIE1, CRIE3 and CRIE5 pumps: • Systems with 2 to 3 pumps = 2” threaded. • Systems with 4 pumps = 2½” threaded. CRIE10 pumps: • Systems with 2 pumps = 2½” threaded. • Systems with 3 to 4 pumps = DN80 flanges. CRIE15 and CRIE20 pumps: • Systems with 2 pumps = DN80 flanges. • Systems with 3 to 4 pumps = DN100 flanges. The number following the pump type designation (1, 3, 5, 10, 15 and 20) indicates the flow rate of the pump in m3/h. * The pumps are available with 1 to 36 impellers/stages (e.g. CRIE5-12 = 12 stages). x1 = U1, U2 or U8 relates to supply voltage (of no importance for drinking water). x2 = Design: A, B or C (of no importance for drinking water). x3 = Staring method: A (of no importance for drinking water). x4 = Product (country) range: A: International range. x5 = Material combination: A: Stainless steel manifold and base frame and standard valves. x6 = Options: A: Standard hydraulic.

Product Images

Approval Holder:

Grundfos Holding A/S

Company Name

Grundfos Holding A/S

Address

Poul Due Jensens Vej 7 Bjerringbro

Postcode

DK-8850

Country

Denmark

Phone

+36302482216

General Email

oszilagyi@grundfos.com

View All Listings by this Company