Range of wedge shoes (part numbers 2005036, 2006536, 2008036, 2010036, 2012536, 2015036, 2020036, 2025036, 2030036, 2040036, 2650036, 2660036, 40005036, 40006536, 40008036, 40010036, 40015036, 40020036, 40025036, 2680036 & 126100036). Black coloured, injection moulded nylon wedge shoes. For use with water up to 50°C.
Injection moulded, glass fibre filled nylon materials. For use with water up to 85°C. LCPA-G(1)06 HMBK001 (black coloured). LCPA-G(1)06 HMNC011 (natural, appears off-white). PA66-G(1)BK011 (black coloured). PA66-G(1)NC011 (natural, appears off-white). (1) 2 digits represent the amount of fiberglass added to the material with a range of 5% (05) - 65%.
'Typlex 3050'. Natural (appears white coloured), extruded PB-1 material. For use with water up to 85°C.
‘LWF LTD FIBRE™MESSENGER PIPE 10/6’. Black coloured, extruded, flexible HDPE pipe. For use with water up to 23°C.
‘GFPP-(1) SFKP (2)’. White coloured, injection moulded, glass fibre reinforced PP material. (1) 2 digits represent the amount of fiberglass added to the material with a range of 5% - 50%. (2) is an internal code used to denote customer and is replaced with a 4 digit number between 0001 & 9999. For use with water up to 85°C.
'SP-402M'. Black coloured, compression moulded natural rubber material. Shore hardness 78. Tested in-radius size 1.0mm. For use with water up to 60°C.
'FFE7018F'. Black coloured, compression moulded EPDM gaskets and 'O' rings. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'9710 'O' Rings'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 75. Tested in-radius size between 0.5mm & 3.4mm. For use with water up to 85°C.
'KX-1'. Black coloured, compression moulded, EPDM rubber sheet material. Shore hardness 75. Tested in-radius size 1.0mm. For use with water up to 85°C.
Initial approval was for ‘SMS-80’ (shore hardness 80) only. In April 2024 ‘SMS-50' (shore hardness 50) & ‘SMS-70’(shore hardness 70) were added to the approval. Black coloured, compression moulded EPDM materials. Shore hardness between 50 & 80. Tested in-radius size 1.0mm. For use with water up to 23°C.
'AquaFlex T 5858'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 70°C.
'EPDM70-BH'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'DQ-EPDM75'. Black coloured, compression moulded EPDM material. Shore hardness 75. Tested in-radius size 1.1mm. For use with water up to 85°C.
'3M Scotch Weld Epoxy Adhesive DP110C'. Site applied, white coloured, two-component epoxy adhesive consisting of a white coloured based and yellow coloured accelerator. Mix parts A & B in a 1:1 volume ratio and apply as per TDS dated May, 2022. Cure for 7 days@23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Griffon UNI-100'. Amber coloured solvent cement intended to join PVC pipe and fittings. Apply as per manufacturer's instructions. Cure for 24 hours@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of single-hole, single outlet (fixed) electronically operated, tap assemblies (chrome plated brass). Flow is controlled by a solenoid valve activated by a touch sensor. The spout outlets incorporate plastic aerators. Max working pressure 8.0 bar. Max operating temperature 65°C.
Range of bottom and side entry BS1212-4 (2016) compact type float operated valves for WC flushing cisterns, delayed or non-delayed fill. The inlet incorporates a strainer. Maximum working pressure - 10 Bar Cold water use only.
Range of BS1212-4 (2016) compact type float operated valves for WC flushing cisterns, bottom or side entry type with brass ½’’ or ¾” BSP inlet. The inlet incorporates a strainer, models incorporate a delay fill function. The bottom entry valves are height adjustable. Maximum working pressure - 10 Bar, Cold water use only.
In-line non-verifiable check valve assembly with integral isolation valve. Consisting of spring loaded resilient trim check valve cartridge housed within a DZR brass body, verified by test (suitable for backflow protection against Fluid Category 2). Compression connection to be used with copper pipe to BS EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of non-verifiable double check valve assemblies consisting of two spring loaded resilient trim in-line check valve cartridges housed in DZR brass bodies. Maximum working pressure 16.0 bar Maximum operating temperature 85°C
Page 290 of 522
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
