‘Polycor LP Gel Coat reinforced with Norsodyne H 13212 TAE laminating resin’. ‘NORSODYNE H 13212 BTAE laminating resin’ was added to the approval in July 2024. ‘Polycor LP Gel Coat’ is a brush or spray applied polyester resin gel coat, available in white or grey colours and is reinforced with Norsodyne H 13212 TAE or NORSODYNE H 13212 BTAE glass fibre laminate. Apply the brush grade as per manufacturer’s technical data sheet ‘7100’ dated 10.10.17 and apply the spray grade as per manufacturer’s technical data sheet ‘7200’ also dated 10.10.17. Cure for 24 hours@25°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘SEA2001’ (manufactured in Italy, Poland & Turkey). Dual layer, extruded, composite hoses. Hoses with a black coloured inner layer and either a red or blue coloured outer layer are suitable for use with water up to 60°C. Hoses with a straw coloured, translucent inner and outer layer are suitable for use with water up to 60°C. Hoses with a black coloured inner layer and either a white or grey coloured outer layer are suitable for use with water up to 23°C. From January 2023 hoses with a black coloured inner layer and either a white or grey coloured outer layer are suitable for use with water up to 60°C.
Range of white coloured (opaque), PP filter media, which comprise of melt blown fibres laid onto an extruded core. ‘SupaGard’ range (complete range except B-Blue) with a micron rating of between 0.5μm & 200 μm. ‘SupaSpun’ (complete range) with a micron rating of between 0.3μm & 180μm. ‘Contour’ (complete range of lengths). For use with water up to 23°C.
'Interflon Paste HT1200'. Cream coloured ceramic paste. Apply as per manufacturer's instructions, document number 'IFUHT1200' dated 24/04/2017. Cure for 5 minutes@22°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated brass finish). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator and a stainless-steel strainer on the inlet. Maximum working pressure 8.0 Bar Maximum operating temperature 70.0°C
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated brass finish). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator and a stainless-steel strainer on the inlet. Maximum working pressure 8.0 Bar Maximum operating temperature 70.0°C
Spring loaded resilient trim check valve cartridge with a plastic body and EPDM ‘O’-rings. For insertion into fittings with specifically sized bores. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C
Spring loaded resilient trim in-line check valve cartridge with acetal body, incorporating a stainless steel spring, EPDM & silicone ‘O’-rings. To be housed in a specifically dimensioned body. Maximum working pressure 14 Bar
Non-metallic materials and components comply with BS6920 at 85°C
Range of one piece water storage cisterns with a screened breather and over flow. Model 46714 iBoost+200 has a rectangular weir overflow Model 46712 iBoost+200 has a circular overflow Cold water only.
Range of self-closing headworks with stainless steel bodies to be housed in specifically dimensioned bodies. Maximum working pressure 8.8 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Page 22 of 101
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
