'Ultrason® S3010 Natural'. Natural (beige coloured), injection moulded polysulphone material. For use with water up to 85°C.
'Ultrason® S2010 Natural'. Natural (colourless), injection moulded polysulphone material. For use with water up to 85°C.
'WS 9000'. Site applied, off-white coloured, fibre glass impregnated, polyurethane repair tape. Apply as per manufacturer's technical date sheet created '02/11/2010' and reviewed '30/01/2015'. Cure for 30 minutes@23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JP EB 750'. Black coloured ebonite rubber manufactured by calendaring. Shore hardness 75 D. Tested in-radius size 1.03mm. For use with water up to 23°C.
'EP6008'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 60. Tested in-radius size 0.8mm. For use with water up to 85°C.
`EP2/9/10 BLK 'O' rings`. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size 1.2mm. For use with water up to 85°C.
`EP11/01/13 BLK 'O' rings & seals`. Black coloured, injection moulded 'O' rings & seals. Shore hardness 60. The 'O' rings have a tested in-radius size of 1.8mm. The seals have a tested in-radius size of 0.75mm. For use with water up to 85°C.
'E70N01C 'O' rings and gaskets'. Black coloured, injection moulded EPDM 'O' rings and gaskets. Shore hardness 70. The 'O' rings have an in-radius size of 0.5mm. The gaskets have an in-radius size of 1.0mm. For use with water up to 85°C.
'EP210107'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 65°C.
'OYRTEP7011PWRC'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.5mm. For use with water up to 65°C.
'ZF-73'. Black coloured, compression moulded EPDM material. Shore hardness 75. Tested in-radius size 1.0mm. For use with water up to 85°C.
‘0250-35 (50A), 0260-35 (60A), 0270-44 (70A), 0280-22 (80A) and 0290-11 (90A)’. Black coloured, compression moulded EPDM materials. Shore hardness between 50A & 90A. Tested in-radius size 1.0mm. For use with water up to 23°C.
‘5052911193 (50A), 5062911233 (60A), 5072911255 (70A), 5082911184 (80A) and 5092911126 (90A)’. Black coloured, compression moulded EPDM materials. Shore hardness between 50A & 90A. Tested in-radius size 1.0mm. For use with water up to 23°C.
‘EW45, EW50, EW53, EW54, EW54W, EW55, EW60, EW65, EW70, EW75, EW80, EW81 & EW85’. Black coloured, compression moulded EPDM rubber materials. Shore hardness between 45 & 85. Tested in-radius size 1.4mm. For use with water up to 60°C.
'REGM20'. Off-white coloured, PTFE paste intended for use as a thread sealant. For use with water up to 23°C.
'114-9100'. Off-white coloured, PTFE paste intended for use as a thread sealant. For use with water up to 23°C.
'MV250 Plus'. Off-white coloured, PTFE paste intended for use as a thread sealant. For use with water up to 23°C.
'THERMOLAST K TF5WHA, TF6WHB, TF6WHA, TF7WHB, TF7WHA, TF8WHB & TF8WHA'. Injection moulded, natural (appears off-white translucent) TPE materials with a shore hardness of between 55 and 85. Tested in-radius size 1.0mm. The materials may be coloured using one, or any combination of, the following Kraiburg pigments (up to and including the maximum level included): Black (maximum level 3%). White (maximum level 2%). Blue (maximum level 2%). Orange (maximum level 2%). Yellow 1 (maximum level 2%). Yellow 2 (maximum level 2%). Yellow 3 (maximum level 2%). Green (maximum level 2%). Red 1 (maximum level 2%). Red 2 (maximum level 2%). Brown (maximum level 2%). For use with water up to 65°C.
Single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The inlet to the solenoid incorporates a stainless-steel strainer. The product is supplied with a stainless-steel braided EPDM lined flexible hose assembly for installation between the solenoid valve and the tap body. The spout outlet incorporates a plastic aerator with built in flow regulator. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of BS1212-4 diaphragm type inlet valves incorporating a plastic body for use in either side or bottom entry WC cisterns. The valves incorporate an up and over discharge, plastic arm and float. The inlet is fitted with a plastic flow regulator and strainer. Maximum working pressure 10 bar. Cold water use only.
Page 21 of 590
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
