‘Corroless RF35 (2024) Coating System’. Site applied, grey coloured (once applied), two-part epoxy coating. The primer comprises of ‘Corroless EPF (2022) Primer Base Red’ and ‘Corroless EPF (2022) Buff Temperate Hardener’, to be mixed in a 1:1 volume ratio and applied as per manufacturer’s TDS issued ‘June 2024’. Cure for 24 hours at 10°C. The coating comprises of ‘Corroless RF35 (2024) Base 00-A-01 Portland’ and ‘Corroless RF35 (2024) Hardener’, to be mixed in 5.5:1 weight ratio and applied as per manufacturer’s TDS issued ‘June 2024’. Cure for 7 days at 10°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5042 Coatings, Paints & Linings

Section Subtitle:

Site applied pipe and fittings coatings. Compliance with BS6920 relates to the conditions of cure specified in the listing. If the cure conditions are varied from those described below then compliance with BS6920 cannot be assummed without further testing. Where catalysts are required, only tested catalysts in the recommended concentrations should be used. Manufacturer's advice must be sought if any non standard mixing or curing conditions are being considered.

WRAS Approval Number:

250755060

Expiry date:

31/07/2030

Approval Holder:

Axalta Coatings Systems Ltd.

Company Name

Axalta Coatings Systems Ltd.

Postcode

NG17 2RG

View All Listings by this Company

'REGZ40 & REGZ41'. white coloured (translucent) silicone grease. Apply as per manufacturer's instructions. For use with water up to 65°C.

Section:

5160 Lubricants

Expiry date:

29/02/2028

Approval Holder:

Regin Products Limited

Company Name

Regin Products Limited

Address

8-13 Tower Square, Huntingdon, Cambridgeshire

Postcode

PE29 7DT

Phone

+44 (0) 1480 412415

General Email

sales@regin.co.uk

View All Listings by this Company

'Grivory GVN-5H black 9915'. Black coloured, injection moulded PA 66 + PA 6I/X-GF50 material. For use with water up to 85°C.

Section:

5180 Nylon

Section Subtitle:

Material only. Components made from materials listed in this section may be required to be submitted for audit tests.

WRAS Approval Number:

250855037

Expiry date:

31/08/2030

Approval Holder:

EMS-CHEMIE AG

Company Name

EMS-CHEMIE AG

Address

Via Innovativa 1, CH-7013 Domat/Ems

Country

Switzerland

Phone

+41 81 632 78 78

General Email

welcome@emsgrivory.com

View All Listings by this Company

'TECHNYL ® SAFE A 219WFC V30 BK’ (black coloured) & ‘TECHNYL ® SAFE A 219WFC V30 NC’ (natural, appears off-white). Injection moulded, glass fibre reinforced polyamide 6.6 materials. For use with water up to 85°C.

Section:

5180 Nylon

Section Subtitle:

Material only. Components made from materials listed in this section may be required to be submitted for audit tests.

WRAS Approval Number:

251155013

Expiry date:

30/11/2030

Approval Holder:

POLYTECHNYL S.A.S. Member of DOMO Chemicals

Company Name

POLYTECHNYL S.A.S. Member of DOMO Chemicals

Address

Usine de Belle Etoile, Avenue Albert Ramboz, 69190 SAINT-FONS

Country

France

View All Listings by this Company

'Seal Ring T11/T21'. Grey coloured, extruded PE seal ring. For use with water up to 85°C.

Section:

5240 Polyethylene

Section Subtitle:

Components. All components listed in this section have been tested for water contact suitability of material only.

WRAS Approval Number:

250955021

Expiry date:

30/09/2030

Approval Holder:

Vanatome (Previously DAHER Valves)

Company Name

Vanatome (Previously DAHER Valves)

Address

Chemin de la buissonnée, 26241 SAINT-VALLIER

Country

France

View All Listings by this Company