Range of indirect heat interface units (HIU) providing heating and instantaneous hot water. The central heating and hot water is generated via plate heat exchangers. Maximum operating pressure 10 bar (primary and DHW secondary). Maximum operating pressure 2.5 bar CH secondary Maximum operating temperature 90°C

Section:

1465 Heaters

Section Subtitle:

Combination boilers and Water Jacketed Tube heaters. Low volume water content. Heat retained in water heaters will cause expansion of water after closure of draw-off taps and valves. Provision for expansion of water must be made to accommodate excess pressure within the system. Particular care is required where check valves are positioned, or loose jumper valves are thought to be upstream of the heater.

WRAS Approval Number:

241104709

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

22mm compression

Marking:

Bosch on front panel and technical info on adhesive label.

Installation Requirements:

R001 R140 R360

Expiry date:

30/11/2029

Model:

7-735-600-739 - Flow 8500 40, 7-735-600-740 - Flow 8500 40 H, 7-735-600-741 - Flow 8500 50, 7-735-600-742 - Flow 8500 50 H, 7-735-600-743 - Flow 8500 60, 7-735-600-744 - Flow 8500 60 H.

Product Images

Approval Holder:

Bosch Thermotechnology Ltd.

Company Name

Bosch Thermotechnology Ltd.

Address

Danesmoor Works Pilsley Clay Cross Chesterfield Derbyshire

Postcode

S45 9BY

View All Listings by this Company

Range of water meters with brass bodies and EPDM ‘O’-rings and plastic strainer on inlet. Maximum working pressure 16 bar. Cold water use only.

Section:

1505 Water Meters

Size:

1 1/4” BSP (M) 1 ½” BSP (M) 2” BSP (M)

Marking:

Resideo & technical information on dial face. Flow arrow cast on body.

Installation Requirements:

R001

Expiry date:

30/09/2028

Model:

EW1100CC2800 EW1100CC3900 EW1100CC4600 EW1100CM2800 EW1100CM3900 EW1100CM4600 - DN25, DN32 and DN40

Approval Holder:

Pittway Sarl

Company Name

Pittway Sarl

Address

A3 - ZA La Pièce 6 1180 Rolle

Country

Switzerland

View All Listings by this Company

Range of water meter manifolds with plastic bodies for use with PE80 pipe (manufactured to BS EN 12201). The inlets incorporate a spherical valve and a check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 16.0 bar. Cold water use only.

Section:

1510 Water Meter Manifolds

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

25mm & 32mm pushfit

Marking:

Atplas logo on body.

Installation Requirements:

R001 R008

Expiry date:

30/11/2029

Model:

MB57425DU Matrix. MB5743225DU Matrix. MB5743232DU Matrix. MB57432DU Matrix. MB5743225DDCV Matrix.

Product Images

Approval Holder:

Atlantic Plastics Ltd.

Company Name

Atlantic Plastics Ltd.

Address

Coytraherne Close, Brackla, Bridgend

Postcode

CF31 2AX

Country

United Kingdom

Phone

01656672628

General Email

rhodgkiss@atplas.co.uk

View All Listings by this Company

Range of water meter manifolds with plastic bodies for use with PE80 pipe (manufactured to BS EN 12201). The inlet incorporates a stop valve. Model MB77025AM Matrix Single (CV) incorporates a single check valve cartridge and model MB77025DCV Matrix Dual (DCV) incorporates two, single check valve cartridges however, the complete products have not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 16.0 bar. Cold water use only.

Section:

1510 Water Meter Manifolds

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

20mm, 25mm & 32mm pushfit

Marking:

Atplas logo on body.

Installation Requirements:

R001 R008

Expiry date:

30/11/2029

Model:

MB77025AM Matrix Single (CV) MB77025DCV Matrix Dual (DCV)

Product Images

Approval Holder:

Atlantic Plastics Ltd.

Company Name

Atlantic Plastics Ltd.

Address

Coytraherne Close, Brackla, Bridgend

Postcode

CF31 2AX

Country

United Kingdom

Phone

01656672628

General Email

rhodgkiss@atplas.co.uk

View All Listings by this Company

Range of water meter manifolds with plastic bodies. The inlets incorporate a stop valve. Model MB77025CG Matrix Single (CV) incorporates a single check valve cartridge and model MB77025CGDCV Matrix Dual (DCV) incorporates two, single check valve cartridges however, the complete products have not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 16.0 bar. Cold water use only.

Section:

1510 Water Meter Manifolds

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

¾” BSP (F)

Marking:

Atplas logo on body.

Installation Requirements:

R001 R008

Expiry date:

30/11/2029

Model:

MB77025CG Matrix Single (CV). MB77025CGDCV Matrix Dual (DCV).

Product Images

Approval Holder:

Atlantic Plastics Ltd.

Company Name

Atlantic Plastics Ltd.

Address

Coytraherne Close, Brackla, Bridgend

Postcode

CF31 2AX

Country

United Kingdom

Phone

01656672628

General Email

rhodgkiss@atplas.co.uk

View All Listings by this Company