Range of wall mounted hose union taps incorporating a brass body with a non-rising spindle headwork and a T type operating member. The JMYG-064 1/2” model incorporates two approved single check valve cartridges (one on the inlet, one on the outlet), however the complete product has not been fully tested to demonstrate it provides backflow protection. Product incorporates a drain plug after the inlet check valve cartridge. Maximum working pressure 10.0 bar. Maximum operating temperature 80°C.
Range of self-closing taps with chromium plated brass bodies, incorporating a non-concussive headwork with or without operating members (see model). The GR 120 + GR 138 + GR 100 model represents three parts which must be installed together to create one complete product. It comprises of a gooseneck spout (chromium plated brass) (GR 120), a single self-closing side valve (brass) incorporating a stainless steel strainer on the inlet (GR 138) and a loose inlet tee piece (chromium plated brass) (GR 100). The inlets of the GR 102M model and the GR 100 tee piece incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. All models, except for the GR 102M model, are supplied with metal back nuts. All spouts incorporate a plastic flow straightener. The GR102M model incorporates a manual temperature control operated by a single lever on the side of the body, on all other models this is achieved via an adjustment plug in the base of the tee piece. Maximum working pressure 10.0 bar. Maximum working temperature 85°C.
‘Tempomix 3’ range of self-closing combination tap assemblies (chromium plated brass) with spring loaded headwork controlling both the flow and temperature with a dome type operating member. The spout outlets incorporate a plastic flow straightener. The inlet hoses each incorporate a plastic strainer and a plastic flow restrictor either side of an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The 794000 and 79400015 models are supplied with ⅜” BSP (M) x ⅜” captive nut inline isolation valves. The 79400015 model is also supplied with a ⅜ BSP (M) x ½” BSP (M) brass adaptor. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Mitsubishi EHWT17D-MHEDW indirectly heated stainless-steel unvented storage cylinder consisting of plate heat exchangers. The secondary circuit is factory fitted with a temperature and pressure relief valve set at 7.0 bar and 90˚C. A safety kit (manifold) consisting of an approved single check valve cartridge (verified by test as suitable for backflow protection against Fluid Category 2), strainer, a pressure relief valve set at 6.0 bar and pressure reducing valve set at 3.5 bar. The space heating circuit is factory fitted with a pressure relief valve fitted rated at 3.0 bar and an automatic air vent. A tundish, expansion vessel and filling loop are also supplied. Maximum secondary (wholesome) circuit working pressure: 5.5 bar. Maximum Space heating (primary) circuit working pressure: 2.5 bar. Maximum brine/ambient circuit working pressure: 9.5 bar. Maximum operating temperature 70°C
‘Comet’ combination units consisting of a cased and insulated stainless steel unvented hot water storage cylinder. The cylinder primary circuit is fitted with an in-line electrical heater which supplies the heat source to the secondary water via a stainless-steel coil, and the heat source to the central heating circuit directly. The cylinder is factory fitted with a temperature and pressure relief valve, pre-set at 7.0 bar 90 degrees. The unit is supplied with an inlet control group containing a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2), pressure reducing valve set at 3.0 bar and an expansion relief set at 6.0 bar. An expansion vessel is factory fitted to both the secondary and primary circuits within and is positioned inside the casing. The primary circuit also incorporates a circulating pump and pressure relief valve which is set at 3.0 bar. Maximum secondary working pressure 5.5 Bar Maximum Primary working pressure 2.5 Bar Maximum operating temperature 65.0 °C
Page 149 of 557
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
