'V- SRPC Portland Cement'. Factory applied, grey coloured Portland Cement. Mixx Sand:water:cement in a weight ratio of 0.6:1.0:0.22. Cure for 96 hours@26°C and then 576 hours@32°C. For use with water up to 65°C.
'Tecnocoat P-2049'. Factory applied, two component, grey coloured polyurea coating. Mix components A & B in a weight ratio of 1:1 and apply as per manufacturer's TDS 'v. 20-03-2022'. Cure for 48 hours@23°C. Between September 2022 and August 2024, the coating is for use with water up to 23°C. From September 2024, the coating is for use with water up to 60°C. This material is only approved for the mixing, curing & soaking conditions that appear on the approval. If the mix/cure/soak conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Interline 925GF (White)'. Site applied, white coloured, two-component, solvent free epoxy coating. Mix part A (white liquid) with part B (off-white liquid) in a volume ratio of 3:1 and apply as per manufacturer's instructions '2253' dated 29/11/2011. Cure for 7 days@25°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Interline 925 White'. Site applied, two-component, white coloured epoxy coating. Mix part A (off-white white coloured liquid) and part B (off-white coloured liquid) in a volume ratio of 3:1 and apply as per manufacturer's instructions ref. '2252', issue date 17/12/2020. Cure for 7 days@25°C. Between January 2022 and August 2022, the coating was for use with water up to 23°C. Between September 2022 and January 2027, the coating is for use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NO MORE DAMP Tanking slurry'. Site applied, grey coloured, cementitious tanking slurry supplied in powder form. Mix powder:water in a mass ratio of 3.85:1 and apply as per manufacturer's datasheet 'issue 5 - MC0420'. Cure for 7 days and 4 hours@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Hydradry Tanking slurry'. Site applied, grey coloured, cementitious tanking slurry supplied in powder form. Mix powder:water in a mass ratio of 3.85:1 and apply as per manufacturer's datasheet 'issue 5 - MC0320'. Cure for 7 days and 4 hours@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SF4300'. Nitrile rubber/aramid fibre, calendered material which is white coloured on one side and green coloured on the other side. For use with water up to 23°C.
'Aropol M 105 TA WRAS’ (formerly known as ‘Aropol M 105 TA’) & ‘Enguard GE NTRL HH WRAS’ (formerly known as ‘Enguard GE NTRL HH'): Translucent straw coloured (glossy one side textured the other), polyester laminating resin manufactured by hand lay-up & gelcoat (brush applied), sheet material. ‘Aropol M 105 TAXR’ & ‘Enguard GE WHI S WRAS’ (formerly known as ‘Enguard GE WHI S’): White coloured (glossy) on one side, translucent straw coloured (textured on the other), polyester laminating resin manufactured by hand lay-up & gelcoat (spray applied), sheet material. Apply as per Ineos Composites method statement ‘Preparation of laminated products for freshwater applications (WRAS)’, ‘code R071, edition 2’ dated 19.1.22. Cure for 9 hours at 23°C with 2% of MEKP-50 catalyst, post-cure for 24 hours@50°C and wash part thoroughly in water before use. For use with water up to 23°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'AXIL-76/T-MD'. White coloured (translucent), extruded silicone rubber hose. Shore hardness 80. Tested in-radius size between 0.75mm & 2.1mm. For use with water up to 85°C.
`BK Standard Lubricant`. Clear (colourless), translucent, soap based lubricant paste. For use with water up to 60°C.
Page 134 of 1180
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
