Range of test port assemblies with DZR brass bodies. Maximum working pressure 25.0 Bar. Maximum operating temperature 100°C.

Section:

1530 Miscellaneous Fittings

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

½” ULF (15mm ULF), ½” LF (15mm LF), ½” (15mm), ¾” (20mm), 1” (25mm), 1”1/4” (32mm), 1”1/2” (40mm), 2” (50mm).

Marking:

RUBINETTERIE logo, flow arrow, thread size, DN, PN, DR and batch number on body.

Installation Requirements:

R001

Expiry date:

31/07/2029

Model:

B-Heat - 200402.

Approval Holder:

Rubinetterie Bresciane Bonomi S.p.A

Company Name

Rubinetterie Bresciane Bonomi S.p.A

Address

Via Massimo Bonomi, 1 Gussago (BS)

Postcode

25064

Country

Italy

Phone

+39 030 82 50 212

View All Listings by this Company

Manufacturer:

Rubinetterie Bresciane Bonomi S.p.A

Company Name

Rubinetterie Bresciane Bonomi S.p.A

Address

Via Massimo Bonomi, 1 Gussago (BS)

Postcode

25064

Country

Italy

Phone

+39 030 82 50 212

View All Listings by this Company

Self-closing hand spray with a stainless-steel body. The inlet incorporates a flow regulator and an approved check valve cartridge (however the complete assembly has not been tested to demonstrate it provides adequate backflow protection). Maximum working pressure 5 bar. Max operating temperature 60°C.

Section:

1535 Miscellaneous

Section Subtitle:

Tap accessories.

WRAS Approval Number:

241004710

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

1/2” BSP (M)

Marking:

T-Safe on body.

Installation Requirements:

R001 R040

Expiry date:

31/10/2029

Model:

02-803200 Kitchen Spray filter

Approval Holder:

T-safe A/S

Company Name

T-safe A/S

Address

Gydevang 1, Alleroed

Postcode

3450

Country

Denmark

Phone

+45 61610518

General Email

moj@t-safe.com

View All Listings by this Company

Range of horizontal multistage close coupled centrifugal pumps incorporating stainless steel cased bodies and impellers. Maximum working pressure: See models. Cold water use only.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

241004726

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

1” BSP (F) - 3” BSP (F). DN40 - DN80 flange.

Marking:

Calpeda and technical info on data plate.

Installation Requirements:

R001 R415

Expiry date:

31/10/2029

Model:

MXH Series: (304 stainless models) MXH/MXHM 202, 203, 204, 205, 206 – 1 ¼” x 1” – 8 bar. MXH/MXHM 402, 403, 404, 405, 406 – 1 1/2” x 1” – 8 bar. MXH/MXHM 802, 803, 804, 805 – 2 ¼” x 1 1/2” – 8 bar. MXH/MXHM 1602, 1603, 1604, 1605, 1606 – 2 ¼” x 1 1/2” – 8 bar. MXH/MXH-F 2001, 2002, 2003, 2004, 2005 – 2 ¼” x 1 1/2” – 10 bar. MXH/MXH-F 3201, 3202, 3203, 3204 – 2 1/2” x 2” – 10 bar. MXH/MXH-F 4801, 4802, 4803 – 3” x 2 1/2” – 10 bar. (316 stainless models) MXHL/MXHLM 202, 203, 204, 205, 206 - 1 ¼” x 1” – 8 bar. MXHL/MXHLM 402, 403, 404, 405, 406 - 1 ¼” x 1” – 8 bar. MXHL/MXHLM 802, 803, 804, 805 - 1 1/2” x 1” – 8 bar. Models Added March 2026: (304 stainless models) MXH 207, 208, 209, 407, 408, 409, 806, 807,808 – 1 ¼” x 1” – 10 bar. MXHM 207, 208, 209, 407, 408 – 1 ¼” x 1” – 10 bar. (316 stainless models) MXHL 207, 208, 209, 407, 408, 409, 806, 807,808 – 1 ¼” x 1” – 10 bar. MXHLM 207, 208, 209, 407, 408 – 1 ¼” x 1” – 10 bar. ‘F’ in the code indictates flanged connection. There are four numbers to identify pump’s size: the first two indicate the flow rate (in m3/h); the second two indicate the number of stage (ex. Mxh 3204: 32 m3/h, 4 stages; mxh 203: 2 m3/h, 3 stages) A letter may be added at the end of the pump model to identify the current motor model fitted to the pump e.g. MXH203* where * can be E, /A, /B, /C etc. Example MXH203/A, MXH204/B etc.

Approval Holder:

Calpeda S.p.A

Company Name

Calpeda S.p.A

Address

Via Roggia Di Mezzo 39 36050 Montoro Vicentino Vicenza

Country

Italy

View All Listings by this Company

Range of horizontal multistage pumps with stainless steel bodies, diffuser and impellers and EPDM ‘O’-rings. The products incorporate a graphite-SiC-EPDM shaft seal. The products incorporate a drain plug. Maximum working pressure 8.5 bar. 9Maximum operating temperature 80°C.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

241002708

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Note:

The discharge from the drain plug must be via a type `AA`, `AB` or `AD` airgap, or in accordance with EN1717.

Size:

U 3S & U 5S models: 1” BSP (F) inlet x 1” BSP (F) outlet. U 7S models: 1¼” BSP (F) inlet x 1” BSP (F) outlet. U 9S models: 1½” BSP (F) inlet x 1¼” BSP (F) outlet. U 18S models: 2” BSP (F) inlet x 1½” BSP (F) outlet.

Marking:

Pentax logo, model code and other technical information on data plate on body.

Installation Requirements:

R001 R415

Expiry date:

31/10/2029

Model:

ULTRA S range: U X(S) - XX/Y (T) Where: U = pump type (ULTRA), X = Nominal flow-rate m³/h (3, 5, 7, 9, 18 see model list), S = ULTRA S range - stainless steel hydraulic part, XX = nominal power HPx100 (50 - 400 see model list), Y = Number of impellers (2 - 7 see model list), T = 3 phase, [blank] = single phase. U 3S models: U 3S-50/2; U 3S-70/3; U 3S-90/4; U 3S-100/5; U 3S-120/6; U 3S-150/7. U 5S models: U 5S-70/2; U 5S-80/3; U 5S-120/4; U 5S-150/5; U 5S-180/6; U 5S-200/7. U 7S models: U 7S-100/2; U 7S-120/3; U 7S-180/4; U 7S-250/5; U 7S-300/6. U 9S models: U 9S-100/2; U 9S-150/3; U 9S-200/4; U 9S-250/5. U 3S models: U 3S-50/2 T; U 3S-70/3 T; U 3S-90/4 T; U 3S-100/5 T; U 3S-120/6 T; U 3S-150/7 T. U 5S models: U 5S-70/2 T; U 5S-80/3 T; U 5S-120/4 T; U 5S-150/5 T; U 5S-180/6 T; U 5S-200/7 T. U 7S models: U 7S-100/2 T; U 7S-120/3 T; U 7S-180/4 T; U 7S-250/5 T; U 7S-300/6 T; U 7S-350/7 T. U 9S models: U 9S-100/2 T; U 9S-150/3 T; U 9S-200/4 T; U 9S-250/5 T. U 18S models: U 18S-180/2 T; U 18S-250/3 T; U 18S-400/4 T.

Approval Holder:

PENTAX INDUSTRIES SpA

Company Name

PENTAX INDUSTRIES SpA

Address

Viale dell’Industria 1 Veronella

Postcode

37040

Country

Italy

Phone

+39 0442 489567

General Email

g.cengia@pentax-pumps.it

View All Listings by this Company

Range of multistage and single stage water pumps with stainless steel bodies and impellers. Maximum working pressure 2.0 bar (AMS models), 4.0 bar (EDH & EMH models) 8.0 bar (LVS models). Maximum operating temperature 85°C

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

241102712

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

Please refer to model.

Marking:

LEO on cover. LEO, model & technical information on date label on body.

Installation Requirements:

R001 R415

Expiry date:

30/11/2029

Model:

EDH (m)XX-XX-F-E 1.m: different phase. --m: single phase, none: three phase. 2.XX: Rated flow (m³/h, range:2~20 m³/h. 3.XX: Impeller progression x10, progression range:1~6. 4.F: F type motor 5.E：E type end connection mode and size -- Rated flow (2 m³/h) :G1"XG1" -- Rated flow (4 m³/h) :G1¼"XG1¼" -- Rated flow (10-20 m³/h) :G2"XG2" AMS(m)XXX-XX-E 1.m: different phase. --m: single phase，none: three phase 2.XXX: Rated flow（L/min） 3. XX: Rated power（kW）. 4.E：E type end connection mode and size -- Rated flow(70-120m³/h) : G1¼"XG1" -- Rated flow(210m³/h) :G1½"XG1¼" -- Rated flow (370 m³/h): G2"XG1¼" LVSXXX-XX-(1/2/C/D/2C/2D/C-D) -(B) -E 1.XXX: Rated flow（m³/h）, Range:1~200 m³/h. 2.XX: Impeller progession，progession range:1~36. 3. 1/2/C/D/2C/2D/C-D: Extra impeller: --1or2，On behalf of the product with 1 or 2 small size impeller. --C or D，On behalf of the product with a size C or size D impeller. --2C or 2D，On behalf of the product with two size C or size D impellers. --C-D, On behalf of the product with a size C and a size D impeller. 4.B: the materials of wetted parts --B，material is SUS 316. --None，material is SUS 304. 5.E：E type end connection mode and size -- Rated flow(1-3m³/h) : DIN Flange connection DN 25 -- Rated flow(4-5m³/h) : DIN Flange connection DN 32 -- Rated flow(10m³/h) : DIN Flange connection DN 40 -- Rated flow(15-20m³/h) : DIN Flange connection DN 50 -- Rated flow(32m³/h) : DIN Flange connection DN 65 -- Rated flow(45m³/h) : DIN Flange connection DN 80 -- Rated flow(64-90m³/h) : DIN Flange connection DN 100 -- Rated flow(120-150m³/h) : DIN Flange connection DN 125 -- Rated flow(200m³/h) : DIN Flange connection DN 150 EMH (m)XX-XX\XX-SE 1.m: different phase. --m: single phase，none: three phase. 2.XX: Rated flow（m³/h），range: 2、3、4、8、10、12、16、20m³/h. 3.XX: impeller progession (1,2,3,4,5,6,7) 4.XX: Small Impeller（1,2,3,4,5, ） 5.SE: SE Intelligent Type End connection mode and size Rated flow (2、3m³ /h) :G1"XG1" Rated flow (4m³ /h) :G1¼"XG1" Rated flow (8、10、12m³ /h) :G1½"XG1½" Rated flow (16、20m³ /h) :G2"XG2"

Manufacturer:

Leo Group Pump(Zhejiang) Co., Ltd

Company Name

Leo Group Pump(Zhejiang) Co., Ltd

Address

No 1,3rd street, East Industry Center,Wenling, Zhejiang, China

View All Listings by this Company