'Ascent-01'. Factory applied, grey coloured, Portland cement mortar. Mix sand, cement and water in a weight ratio of 1:1:0.35 and apply as per manufacturer's user instructions 'doc: Ascent-01', 'vision: A08052023', dated '2023-05-08'. Cure for 24 hours@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5030 Coatings, Paints & Linings

Section Subtitle:

Factory applied pipe & fittings coatings.

WRAS Approval Number:

2310518

Expiry date:

31/10/2028

Approval Holder:

Shanxi Ascent Industrial Co., Ltd.

Company Name

Shanxi Ascent Industrial Co., Ltd.

Address

Floor 8, Tianjia Building, Xiaodian District, Taiyuan, Shanxi

Country

China

View All Listings by this Company

'Eucoflex Caliente'. Site applied, blue coloured, two-component polyurea coating consisting of Component A, Component B and Component C (Pigment Paste). Mix & apply as per manufacturers datasheet 'TX40T815', dated 'August 2023'. For use with water up to 60°C. This approval is valid only for the material when it is applied by experienced, suitably trained applicators that are authorized and/or certified by Euclid Chemical Toxement. The authorization, training and certification of the local applicators are the responsibility of Euclid Chemical Toxement and not the responsibility of WRAS.

Section:

5042 Coatings, Paints & Linings

Section Subtitle:

Site applied pipe and fittings coatings. Compliance with BS6920 relates to the conditions of cure specified in the listing. If the cure conditions are varied from those described below then compliance with BS6920 cannot be assummed without further testing. Where catalysts are required, only tested catalysts in the recommended concentrations should be used. Manufacturer's advice must be sought if any non standard mixing or curing conditions are being considered.

WRAS Approval Number:

2208608

Expiry date:

31/08/2027

Approval Holder:

Euclid Chemical Toxement

Company Name

Euclid Chemical Toxement

Address

Parque Industrial Gran Sabana, Tocancipa, Colombia

View All Listings by this Company

'LOCTITE GeoSpray Mortar'. Site applied, grey coloured, geopolymer cementitious material. Mix 300g of powder with 60ml water and apply as per manufacturer's instructions 'V: 09.06.2022'. Cure for 96 hours@3°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5042 Coatings, Paints & Linings

Section Subtitle:

Site applied pipe and fittings coatings. Compliance with BS6920 relates to the conditions of cure specified in the listing. If the cure conditions are varied from those described below then compliance with BS6920 cannot be assummed without further testing. Where catalysts are required, only tested catalysts in the recommended concentrations should be used. Manufacturer's advice must be sought if any non standard mixing or curing conditions are being considered.

WRAS Approval Number:

2310509

Expiry date:

31/10/2028

Approval Holder:

Henkel Corporation

Company Name

Henkel Corporation

Address

One Henkel Way, Rocky Hill, 06067

Country

United States

View All Listings by this Company

'P0667 Lid Support'. Light green coloured (opaque), GRP lid support component manufactured by pulltrusion. For use with water up to 23°C.

Section:

5120 Glass Reinforced Plastics (GRP)

Section Subtitle:

Components.

WRAS Approval Number:

2308546

Expiry date:

31/08/2028

Approval Holder:

Pultrex Ltd.

Company Name

Pultrex Ltd.

Address

Units 18-20, Riverside Avenue West, Lawford, Manningtree, Essex

Postcode

CO11 1UN

View All Listings by this Company

'DISTITRON® VE 100 ST'. Beige coloured, glass fibre reinforced Vinyl Ester Resin manufactured by hand lay-up. For use with water up to 23°C.

Section:

5125 Glass Reinforced Plastics (GRP)

Section Subtitle:

Material only. Components made from materials listed in this section may be required to be submitted for audit tests.

WRAS Approval Number:

2309517

Expiry date:

30/09/2028

Approval Holder:

Polynt S.p.A.

Company Name

Polynt S.p.A.

Address

Via del Pruneto 40, 52027 San Giovanni Valdarno, Arezzo

Country

Italy

General Email

contact@polynt.com

View All Listings by this Company