Water conditioners, de-scalers, phosphate dosing, magnetic, electrolytic and electronic
Section Code 2410 : Fittings in this section have been judged only against the requirements of The Water Supply (Water Fittings) Regulations 1999 (England and Wales), The Water Supply (Water Fittings) (Scotland) Byelaws 2014 or The Water Supply (Water Fittings) Regulations (Northern Ireland) 2009. The decision of the Scheme to list them is not to be taken as any guide as to their effectiveness to do the job for which they have been designed. It should also be noted that there is a likelihood of some materials being leached into the water, which together with materials already in the water at source, could exceed the maximum limits set in the EC Directive on Water Quality and therefore it is recommended that before putting such units into service where the water may be ingested, advice should first be sought from the Water Undertaker.
Back To Directory Sections
WRAS Approval Number: #1912004
Magnetic boiler cleanser with chromium plated brass body incorporating isolation valves on the inlet and outlet and a drain valve incorporating an isolation ball valve on the plastic filter.
Maximum working pressure 4.0 bar. Maximum operating temperature 100ºC
- Section:
- 2410 Water conditioners, de-scalers, phosphate dosing, magnetic, electrolytic and electronic
- WRAS Approval Number:
- 1912004
- Expiry date:
- 31/12/2024
- Size:
- 22mm compression x 22mm compression
- Marking:
- MSL drain valve body.
Flow arrow on valve body.
- Installation Requirements:
- R001 R120 R150 R170 R290
- Model:
-
BFMBC-BLU22
- Approval Holder:
- Navigator MSL Ltd.
Company Name
Navigator MSL Ltd.
Address
Mill Road,
Sharnbrook,
Beds.
Postcode
MK44 1NP
Phone
01234 781234
View All Listings by this Company
WRAS Approval Number: #1912051
IPS KalyxX range of in line galvanic water treatment conditioners with stainless steel bodies and POM-C core tube.
Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
- Section:
- 2410 Water conditioners, de-scalers, phosphate dosing, magnetic, electrolytic and electronic
- WRAS Approval Number:
- 1912051
- Expiry date:
- 31/12/2024
- Size:
- ½” BSP (F)
¾” BSP (F)
1” BSP (F)
- Marking:
- Swiss Aqua Technologies and logo, IPS Kalyxx Red Line, flow arrow, technical information and date of manufacture (YYYY) on body
- Installation Requirements:
- R001 R120 R150 R170 R290
- Model:
-
RedLine 1/2", RedLine 3/4", RedLine 1"
- Approval Holder:
- Swiss Aqua Technologies AG
Company Name
Swiss Aqua Technologies AG
Address
SAT R&D Department
Rusinska 15113/9
Presov
Postcode
08001
Country
Slovakia
General Email
michal.spak@swatec.ch
View All Listings by this Company
WRAS Approval Number: #1912057
IPS KalyxX Homescale Protect Range of in line galvanic water treatment conditioners with stainless steel bodies and POM-C core tube.
Maximum working pressure 10.0 bar. Maximum operating temperature 85°C
- Section:
- 2410 Water conditioners, de-scalers, phosphate dosing, magnetic, electrolytic and electronic
- WRAS Approval Number:
- 1912057
- Expiry date:
- 31/12/2024
- Size:
- ½” BSP (F)
¾” BSP (F)
1” BSP (F)
- Marking:
- IPS, MODEL & TECHNICAL INFORMATION ON ADHESIVE LABEL ON BODY
IPS, MODEL, HOMESCALE PROTECT & FLOW ARROW ON BODY
- Installation Requirements:
- R001 R120 R150 R170 R290
- Model:
-
IPS KalyxX Homescale Protect 1/2", IPS KalyxX Homescale Protect 3/4" & IPS KalyxX Homescale Protect 1"
- Approval Holder:
- APP WHOLESALE LTD
Company Name
APP WHOLESALE LTD
Address
UNITS 12-14 STERLING INDUSTRIAL ESTATE
RAINHAM ROAD SOUTH
DAGENHAM
Postcode
RM10 8TX
Country
ESSEX
View All Listings by this Company
WRAS Approval Number: #2001004
`Water block` self-closing valve with magnetic scale inhibitor and grey plastic body and a gear driven volume-controlled operation device. The product incorporates a combined EPDM washer and stainless steel strainer and EPDM ‘O’-rings.
The product is designed to stop the flow of water once a pre-set value (in litres) has been reached. User intervention is then required to reset it.
Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
- Section:
- 2410 Water conditioners, de-scalers, phosphate dosing, magnetic, electrolytic and electronic
- WRAS Approval Number:
- 2001004
- Expiry date:
- 31/01/2025
- Note:
- The self-closing function once a pre-set value has been reached has not been assessed and is not considered to be covered by the scope of this approval.
- Size:
- ¾” BSP (F) inlet and ¾” BSP (M) outlet
- Marking:
- Eltek, water block, max flow rate and flow arrow on body.
- Installation Requirements:
- R001 R120 R150 R170 R290
- Model:
-
101179xx
The ‘x’ is replaced by a number ‘0’ to ‘9’ which denotes the setting notches regulation and packaging type.
- Approval Holder:
- Eltek SpA
Company Name
Eltek SpA
Address
Strada Valenza 5/A
Casale Monferrato
Postcode
15033
Country
Italy
Phone
+39 0142 335511
General Email
f.ruzzafante@eltekgroup.it
View All Listings by this Company
WRAS Approval Number: #2005025
Range of water conditioners incorporating Ball valves. TurboMAG models Simplex, Duplex Skid, Duplex Wall and Quadplex Skid incorporate approved check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection.
Maximum working pressure 10.0 bar.
- Section:
- 2410 Water conditioners, de-scalers, phosphate dosing, magnetic, electrolytic and electronic
- WRAS Approval Number:
- 2005025
- Expiry date:
- 31/05/2025
- Note:
- Cold water use only.
- Size:
- See model
- Marking:
- Hydotec, model, size, pressure and operating info on label on body.
- Installation Requirements:
- R001 R120 R170 R290
- Model:
-
TurboMAG Simplex - 1" BSP (M)
TurboMAG Duplex Skid - 1.5" BSP (M)
TurboMAG Duplex Wall - 1.5" BSP (M)
TurboMAG Quadplex Skid - 2" BSP (M)
TurboMAG Quadplex Vessel - DN50 Flanged.
- Approval Holder:
- Hydrotec International Water Treatment Limited
Company Name
Hydrotec International Water Treatment Limited
Address
38 Main Street
Swords Country
Dublin
Country
Ireland
View All Listings by this Company
WRAS Approval Number: #2006054
Range of water conditioners with stainless steel or brass/copper alloy.
Maximum working pressure 10.0 bar. Maximum operating temperature 100ºC.
- Section:
- 2410 Water conditioners, de-scalers, phosphate dosing, magnetic, electrolytic and electronic
- WRAS Approval Number:
- 2006054
- Expiry date:
- 30/06/2025
- Marking:
- Suprion, model, serial number, flow arrow and other product info on label on body
- Installation Requirements:
- R001 R120 R150 R170 R290
- Model:
-
Model type A (Brass and copper alloy)
JS-12E15: 15mm compression x 15mm compression.
JS-75E22: 22mm compression x 22mm compression.
EH-12F: ½” BSP (M) x ½” BSP (M).
EH-75E22: 22mm compression x 22mm compression.
Model type B (Fibre glass and copper alloy)
JS-75: ¾” BSP (F) x ¾” BSP (F).
JS-100: 1” BSP (F) x 1” BSP (F).
JS-125: 1 ¼” BSP (F) x 1 ¼” BSP (F).
JS-150: 1 ½” BSP (F) x 1 ½” BSP (F).
EH-75: ¾” BSP (F) x ¾” BSP (F).
EH-100: 1” BSP (F) x 1” BSP (F).
EH-125: 1 ¼” BSP (F) x 1 ¼” BSP (F).
EH-150 : 1 ½” BSP (F) x 1 ½” BSP (F).
Model type C (Fibre glass and steel)
JS-250: 2 ½” BSP (F) x 2 ½” BSP (F).
JS-400: 4” BSP (F) x 4” BSP (F).
EH-250: 2 ½” BSP (F) x 2 ½” BSP (F).
EH-400: 4” BSP (F) x 4” BSP (F).
- Approval Holder:
- Ion Water Products Ltd
Company Name
Ion Water Products Ltd
Address
Terminus Road
Chichester
West Sussex
Postcode
PO19 8DW
View All Listings by this Company - Manufacturer:
- Sunward Co Ltd
Company Name
Sunward Co Ltd
View All Listings by this Company
WRAS Approval Number: #2011080
WRAS Approval Number: #2102702
WRAS Approval Number: #2102704
Electrolytic scale inhibitor incorporating a nickel plated copper body.
Maximum working pressure 10.0 bar. Cold water use only.
- Section:
- 2410 Water conditioners, de-scalers, phosphate dosing, magnetic, electrolytic and electronic
- WRAS Approval Number:
- 2102704
- Expiry date:
- 28/02/2026
- Size:
- 22mm compression
- Marking:
- Altecnic, DirtMag iQ, Size and other info on adhesive label on body.
- Installation Requirements:
- R001 R120 R150 R170 R290
- Model:
-
ALTECNIC DIRTMAG iQ ELECTROLYTIC SCALE INHIBITOR 114-9005.
- Approval Holder:
- Altecnic Limited
Company Name
Altecnic Limited
Address
Mustang Drive
Stafford
Staffordshire
Postcode
ST16 1GW
Country
United Kingdom
Phone
+44 (0)1785 218200
General Email
gary.perry@altecnic.co.uk
View All Listings by this Company
WRAS Approval Number: #2102703
Page 1 of 8
