'Weberdry epo PW'. Site applied, light grey coloured (once mixed), two-component epoxy coating. Mix Part A (light grey coloured) with Part B (translucent, yellow coloured) in a weight ratio of 100:20. Apply as per manufacturer's TDS 'Edition: 04.23-A'. Cure for 24 hours@25°C. Mix and apply a second coat in the same way and then cure for 14 days@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5042 Coatings, Paints & Linings

Section Subtitle:

Site applied pipe and fittings coatings. Compliance with BS6920 relates to the conditions of cure specified in the listing. If the cure conditions are varied from those described below then compliance with BS6920 cannot be assummed without further testing. Where catalysts are required, only tested catalysts in the recommended concentrations should be used. Manufacturer's advice must be sought if any non standard mixing or curing conditions are being considered.

WRAS Approval Number:

2304544

Expiry date:

30/04/2028

Approval Holder:

Sodamco Emirates factory LLC

Company Name

Sodamco Emirates factory LLC

Address

ICAD3, Plot 65 NP29, Abu Dhabi

Country

United Arab Emirates

View All Listings by this Company

`EcoZmart Waterproofing`. Site applied, grey coloured tanking slurry. Mix tanking slurry with water in a 3:1 volume ratio and apply coat 1 as per manufacturer's IFU 'TCOWP001', dated '26/05/2023'. Cure for 24 hours@7°C. Mix tanking slurry with water in a 3:1 volume ratio and apply coat 2, 24 hours after the first coat, as per manufacturer's IFU IFU 'TCOWP001', dated '26/05/2023'. Cure for 14 days@7°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5055 Concrete, Cement and Mortar

Section Subtitle:

Waterproofers.

WRAS Approval Number:

2208607

Expiry date:

31/08/2027

Approval Holder:

TCO International Holdings

Company Name

TCO International Holdings

Address

128 City Road, London

Country

EC1V 2NX

View All Listings by this Company

'Vinoleo 77/14'. Amber coloured, soap based lubricant. Apply as per manufacturer's instructions. For use with water up to 23°C.

Section:

5160 Lubricants

Expiry date:

31/07/2028

Approval Holder:

MacDermid Ltd.

Company Name

MacDermid Ltd.

Address

BSA Business Park, 198 Golden Hillock Road, Small Heath, Birmingham

Postcode

B11 2RQ

Phone

0121 606 8100

View All Listings by this Company

'PPELXS314G20NA'. Beige coloured, injection moulded PPE material. For use with water up to 85°C.

Section:

5253 Polyphenylene Ether (PPE)

Section Subtitle:

Material only. Components made from materials listed in this section may be required to be submitted for audit tests.

WRAS Approval Number:

2302531

Expiry date:

29/02/2028

Approval Holder:

Nantong Xingchen Synthetic Material Co., Ltd.

Company Name

Nantong Xingchen Synthetic Material Co., Ltd.

Address

118, Jianggang Rd, Nantong Economic Development Zone， Nantong, Jiangsu

Country

China

View All Listings by this Company

'DIC.PPS FZ-2140-F3 BLACK'. 'DIC.PPS FZ-2140-F3 BLACK-U' was added to the approval in September 2023. Black coloured, injection moulded PPS materials manufactured in Vienna, Austria. For use with water up to 85°C.

Section:

5255 Polyphenylene Sulphide (PPS)

Expiry date:

30/06/2028

Approval Holder:

DIC Corporation

Company Name

DIC Corporation

Address

12, Yawata-kaigandori, Ichihara, 290-8585

Country

Japan

View All Listings by this Company