Range of screw down stop valves with plastic bodies for below ground use.. The valves are supplied with loose pipe inserts and are for use with polyethylene pipe (manufactured to BS EN 12201). Maximum working pressure 14.0 bar. Cold water use only.

Section:

2320 Valves

Section Subtitle:

Stop, plastic, screw down.

WRAS Approval Number:

241102022

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

20mm, 25mm and 32mm compression.

Marking:

Philmac logo on operating member. Philmac logo, size and flow arrow on body.

Installation Requirements:

R001

Expiry date:

30/11/2029

Model:

Philmac 3G range of valves comprising of models: 81283110, 81283210, 81284210, 81284310, 81282200, 81283300 & 81284400

Manufacturer:

Philmac Pty Ltd.

Company Name

Philmac Pty Ltd.

Address

47-59 Deeds Road, North Plympton, SA 5037

Country

Australia

View All Listings by this Company

'PRIMGREEN® ENDURANCE & Primgreen LAT 12035' primers for use with 'RILSAN® PA11 T BLUE 7444 MAC (16293), PA11 T GREY 5161 MAC (17203), PA11 T WHITE 1488 AC (17219) & PA11 T BLACK 7450 AC (17185)' coatings. Factory applied primers and powder coatings. The piece to be coated is to be pre-heated to 330°C for 10 minutes, the primer and coating applied in accordance with user instructions 'Dircom - 4418E/05.2015/20' and then cured for 10 minutes@330°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5030 Coatings, Paints & Linings

Section Subtitle:

Factory applied pipe & fittings coatings.

WRAS Approval Number:

240855041

Expiry date:

31/08/2029

Approval Holder:

Arkema France

Company Name

Arkema France

Address

CERDATO, Route du Launay, 27470 Serquigny

Country

France

View All Listings by this Company

'V-PET#1340QD-F GRAY'. Factory applied, grey coloured epoxy resin coating. Apply as per manufacturer's instructions '2211447-2' dated '2023/11/16'. Cure for 20 minutes@180°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5030 Coatings, Paints & Linings

Section Subtitle:

Factory applied pipe & fittings coatings.

WRAS Approval Number:

241155040

Expiry date:

30/11/2029

Approval Holder:

KUBOTA Corporation

Company Name

KUBOTA Corporation

Address

1-3, Kyobashi 2-chome, Chuo-ku Tokyo, 104-8307

Country

Japan

Phone

+81-90-2492-1627

View All Listings by this Company

'PE 7144 Plastic Sleeve'. Natural (appears white), injection moulded polyethylene component. For use with water up to 85°C.

Section:

5240 Polyethylene

Section Subtitle:

Components. All components listed in this section have been tested for water contact suitability of material only.

WRAS Approval Number:

241055024

Expiry date:

31/10/2029

Approval Holder:

Ferroli Ltd

Company Name

Ferroli Ltd

Address

Lichfield Road, Branston Industrial Estate, Burton on Trent

Postcode

DE14 3HD

Country

Staffordshire

Phone

+44 870 7282882

General Email

technical@ferroli.co.uk

View All Listings by this Company

'EP701443C 'O' rings'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size 1.75mm. For use with water up to 85°C.

Section:

5360 Rubbers

Section Subtitle:

Ethylene Propylene Diene Monomer (EPDM) - components.

WRAS Approval Number:

240955030

Expiry date:

30/09/2029

Approval Holder:

Fannteer Corporation

Company Name

Fannteer Corporation

Address

2F, No. 77, Zhouzi Street, Neihu District, Taipei City 114680

Country

Taiwan

Phone

+886 2 2577 4691

General Email

info@fannteer.com.tw

View All Listings by this Company