Range of press fit screw down stop valves with brass bodies and EPDM seals. For use with copper pipe to EN1057. Maximum working pressure 16.0 Bar Maximum operating temperature 85 °C.
Range of double regulating valves available with bronze bodies, incorporating a non-rising spindle headwork. Products also include two test ports. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
'POMM90 Black' (black coloured), ‘POMM90 Dark grey’ & ‘POMM90 Grey’ (grey coloured). Injection moulded POM materials. For use with water up to 85°C.
'KOCETAL K100 GMP'. White coloured, injection moulded acetal material. For use with water up to 85°C.
'ABS GAR-220 SA'. Natural (appears yellow coloured), injection moulded ABS material. For use with water up to 85°C.
'PGS3'. Grey coloured, compression moulded, Silicon Carbide, ring shaped seal/washer. For use with water up to 85°C.
'JA-Blue'. Factory applied, blue coloured epoxy powder coating. Pre-heat substrate to 40°C and then spray apply as per manufacturer's instructions issued ‘March 2017, V4.1’. Cure for 20 minutes@180°C. For use with water up to 85°C.
‘SIGMAPRIME 700 HSV’ (yellow/green) Primer for use with ‘SIGMAGUARD CSF 650’ (green) Coating. Factory applied, teal green coloured (once applied), two-component epoxy coating system (manufactured in PPG SSC Co., Ltd. in Ulsan, South Korea). Mix parts A & B of ‘SIGMAPRIME 700 HSV’ (yellow/green) Primer in an 80:20 volume ratio and apply as per manufacturer’s Product Data Sheet ‘Ref. P757’, dated ‘February 20 2025 (Revision of February 10 2025)’. Cure for 24 hours@20°C. Mix parts A & B of ‘SIGMAGUARD CSF 650’ (green) Coating in an 80:20 volume ratio and apply as per manufacturer’s Product Data Sheet ‘Ref. 7443’, dated ‘March 18 2025 (Revision of December 13 2024)’. Cure for 5 days@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘SIGMAPRIME 200’ (yellow/Green) Primer for use with ‘SIGMAGUARD CSF 650’ (green) Coating. Factory applied, teal green coloured (once applied), two-component epoxy coating system (manufactured by PPG SSC Co., Ltd. in Ulsan, South Korea). Mix parts A & B of ‘SIGMAPRIME 200’ (yellow/Green) Primer in an 80:20 volume ratio and apply as per manufacturer’s Product Data Sheet ‘Ref. 7416’, dated ‘June 06 2025 (Revision of May 01 2025)’. Cure for 24 hours@20°C. Mix parts A & B of ‘SIGMAGUARD CSF 650’ (green) Coating in an 80:20 volume ratio and apply as per manufacturer’s Product Data Sheet ‘Ref. 7443’, dated ‘March 18 2025 (Revision of December 13 2024)’. Cure for 5 days@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘SIGMAPRIME 700 HSV’ (yellow/Green) Primer for use with ‘SIGMAGUARD CSF 650’ (green) Coating. Factory applied, teal green coloured (once applied), two-component epoxy coating system (manufactured by PPG Coatings (Kunshan) Co., Ltd. in Kunshan, China). Mix parts A & B of ‘SIGMAPRIME 700 HSV’ (yellow/Green) Primer in an 80:20 volume ratio and apply as per manufacturer’s Product Data Sheet ‘Ref. P757’, dated ‘February 20 2025 (Revision of February 10 2025)’. Cure for 24 hours@20°C. Mix parts A & B of ‘SIGMAGUARD CSF 650’ (green) Coating in an 80:20 volume ratio and apply as per manufacturer’s Product Data Sheet ‘Ref. 7443’, dated ‘March 18 2025 (Revision of December 13 2024)’. Cure for 5 days@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 773 of 816
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
