Luberpox – 2K – DS-Lackfarbe IV80, Wilo Grün nach Muster/IW80 Hardener (green coloured) & Luberpox – 2K – DS-Lackfarbe IV80, RAL 9011 Graphitschwarz/IW80 Hardener (black coloured). Factory applied epoxy coatings. Mix in a 5:1 weight ratio and apply as per Berger-Lacke Technical Data Sheet (rev. 41-06.11.2023). Cure for 7 days at 22°C. For use with water up to 23°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'RTU AL 5002'. Factory applied, blue coloured enamel coating. Apply as per manufacturer's TDS 'TDS/05002', version '09-2023' and fire for 7 minutes@860°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'LZYX002'. Factory applied, grey coloured cement mortar. Mix cement:sand:water in a 1:3.0:0.4 weight ratio and apply as per Instruction Sheet '201 8 07 0', revision 'A2'. Air cure for 4 hours@23°C and the steam cure for 6 hours@60°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Welmortar-BFS'. Factory applied, grey coloured cement mortar. Mix sand:cement:water in a 3:2:1 weight ratio and apply as per manufacturer's SOP document 'WDIPL/QA/WI/14B', revision '01', dated '08.02.2023'. Cure for 28 days@30°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Welmortar-SRP'. Factory applied, grey coloured cement mortar. Mix sand:cement:water in a 3:2:1 weight ratio and apply as per manufacturer's SOP document 'WDIPL/QA/WI/14C', revision '1', dated '08.02.2023'. Cure for 28 days@30°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Pilotpack 3480, 5035, 3435, 4040, 7099, 3408, 3410 & 5020’ range of gland packings. 3480 & 3435 are dark grey coloured, graphitised PTFE based. 5035 is yellow & black coloured, graphitised PTFE/aramid based. 4040 is grey coloured, graphite based. 7099 is white coloured, acrylic/PTFE based. 3408 is white coloured, lubricated PTFE based. 3410 is white coloured, lubricated PTFE based. 5020 is light yellow coloured, lubricated aramid based. All grades are for use with water up to 85°C. For use only as gland packing material having been tested at a reduced surface area to volume ratio.
'FH42Z', grey coloured, compression moulded carbon graphite disc. ‘FH82Z’, grey coloured, compression moulded carbon graphite disc was added to the approval in February 2024. Both are for use with water up to 85°C.
'Drincable'. Blue coloured, extruded, EPDM rubber electrical cable. Shore hardness 50. Tested in-radius size 0.90mm. For use with water up to 23°C. This approval is for complete cable, the blue coloured outer part being the water contact layer.
'EcoPaXX Q-DWX12 BK00002'. Black coloured, injection moulded polyamide material. For use with water up to 85°C.
'Pemaron660G6W NC01'. Natural (appears off-white), injection moulded, glass-reinforced PA66 material. For use with water up to 85°C.
Page 673 of 1117
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
