'Cage Overmould 214867'. Black coloured, injection moulded ABS component. For use with water up to 70°C.
`3M™ Scotchkote™ Fusion-Bonded Epoxy Coating 134`. Factory applied, green coloured, epoxy coating. Pre-heat substrate to 232°C, before dip coating as per manufacturer’s data sheet and application guide ‘78-8141-8528-2 Rev A’ dated February 2016, for 3 seconds. Cure for 10 minutes at 232°C. For use with water up to 23°C. This material is only approved for the application and curing conditions that appear on the approval. If the application and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Resicoat factory applied, epoxy powder coatings. The coatings are electrostatically applied by spray onto a panel pre-heated for 15 minutes@225°C and then post cured for 15 minutes@220°C. For use with water up to 85°C. The following grades are manufactured at GERMANY, REUTLINGEN: Resicoat R4 blue: R4-ES HJ601R, R4-ES HJ605R, R4-ES HJ606R, R4-FB HJC04R, R4-FB HJC06R, R4-FB HJC08R, R4-FB HJC12R, R4-FB HJC33R, R4-FB HJC34R, R4-FB HJC36R, R4-ES HJF01R, R4-ES HJF09R, R4-ES HJF10R, R4-ES HJF13R PAM blue, R4-ES HJF14R, R4-ES HJF22R, R4-ES HJF23R, R4-ES HJF24R, R4-ES HJF26R, R4-ES HJF42R, R4-ES HJG05R, R4-ES HJG07R, R4-ES HJG08R, R4-ES HJH01R & R4-FB HJC26R. Resicoat R4 red/red-brown: R4-FB HGC07R, R4-FB HGC17R, R4-ES HGF03R, R4-ES HGF04R, R4-ES HGF10R, R4-ES HGF17R, R4-ES HGF20R, R4-ES HGH02R. Resicoat R4 black: R4-ES HNF04R & R4-FB HNC01R. Resicoat R4 green: R4-FB HKC71R. Resicoat R8 blue: R8-ES HJF97R, R8-FB HJC37R, R8-FB HJC38R, R8-ES HJG13R, R8-FB HJC50R, R8-FB HJC51R, R8-FB HJC52R, R8-FB HJC53R, R8-FB HJC54R, R8-ES HJF1KR, R8-ES HJF2KR, R8-ES HJF3KR, R8-ES HJF4KR, R8-ES HJF5KR, R8-ES HJF6KR, R8-ES HJG29R & R8-ES HJ609R. Resicoat R8 blue grades added in July 2024: R8-FB HJC55R, R8-ES HJF4MR & R8-ES HJF5LR. Resicoat R8 red/red-brown: R8-FB HGC12R, R8-ES HGF66R, R8-ES HGF67R & R8-ES HGF68R. Resicoat R8 red added in February 2025: R8-ES HGF65R. Resicoat R8 black: R8-ES HNC03R & R8-ES HNF43R. Resicoat R2 blue: R2-ES HJF5BR & R2-ES HJF4ER. The following grades are manufactured at USA, NASHVILLE: Resicoat R4 blue: R4-ES HJ606R, R4-ES HJF10R, R4-ES HJF24R & R4-ES HJF42R. Resicoat R4 red/red-brown: R4-FB HGC17R & R4-ES HGF17R. Resicoat R4 green: R4-ES HKF47R. The following grades are manufactured at CHANGZHOU, CHINA: Resicoat R2 blue: R2-ES HJF5BR. Resicoat R4 blue: R4-FB HJC03R, R4-FB HJC06R, R4-FB HJC08R, R4-FB HJC15R, R4-FB HJC23R, R4-FB HJC29R, R4-ES HJF01R, R4-ES HJF10R, R4-ES HJF13R, R4-ES HJF14R, R4-ES HJF22R, R4-ES HJF24R & R4-ES HJF42R. Resicoat R4 red/red-brown: R4-ES HGF03R, R4-ES HGF04R & R4-ES HGF17R. Resicoat R4 black: R4-ES HNF04R. Resicoat R8 blue grades added in February 2025: R8-FB HJC50R, R8-ES HJF3KR, R8-ES HJF97R The following grades are manufactured at IZMIR, TURKEY: Resicoat R2 blue: R2-ES HJF3D4 & R2-ES HJF4D4. Resicoat R4 blue: R4-ES HJF1C4 & R4-ES HJF2C4. Resicoat R8 blue added in February 2025: R8-ES HJF5M4 The following grades are manufactured at THANE, INDIA: Resicoat R2 blue: R2 HJC43N, R2 HJF2HN, R2 HJF5BR. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'35000 Kanpoly Purco'. Factory applied, two-component, blue coloured, solvent-free polyurethane based coating. Mix and apply as per manufacturer's instructions '0141', 'revision 02' dated February 2022. Cure for 7 days@23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EPACRETE EPAPOX 25 & EPAPROOF FPCS WFC'. Factory applied, cream coloured (once mixed and applied), two-part polyurea coating system. 'EPACRETE EPAPOX 25’ is a two-component epoxy primer which is to be mixed in a 2:1 weight ratio and applied in accordance with manufacturer’s TDS ‘EN 1504-2’, revision date 01.140317. ‘EPAPROOF FPCS WFC' is a two-component polyurea coating which is to be mixed in a 1:1 ratio and applied in accordance with manufacturer’s TDS ‘EN 1504-2’, revision date ’01-2020’. Cure for 24 hours at 25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 66 of 232
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
