'ZMF7405'. Factory applied, blue coloured Enamel coating. Apply as per manufacturer's TDS 'Version 01', issue date 'December 1, 2025'. Dry for 15 minutes@100°C and then furnace fire for 10 minutes@860°C. For use with water up to 85°C.
‘Nelfapox FW Inert Cream'. Factory applied, cream coloured, two-component epoxy coating. Mix base and curing agent in a 6.8:2 volume ratio. Apply one or two coats as per manufacturer's Technical Data Sheet '999', revision date '24-03-2026'. Cure Coat 1 for 16 hours@20°C. Cure Coat 2 for 7 days@20°C. For use with water up to 60°C. These materials are only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'NextGen NP-F9500 PW'. Factory applied, blue coloured powder coating. Apply as per National Paints technical data sheet 'FBE/ REV01 09-07-2019'. Cure for 3 minutes@240°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ConProtect WP 1'. Liquid concrete admixture based on crystallization technology. To be added at a maximum of 2% of the cement weight as per manufacturer's TDS 'Version 3 - 2025'. Cure for 14 days@23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Revolve M-638, M-694 & M-695'. Black coloured Polyethylene materials manufactured using rotational moulding. For use with water up to 85°C.
‘BOR Plus Faser Composite Stabil Pipe PP-R (SDR 6 & SDR 7.4)’. Extruded, multi-layered PP-R pipes comprising of a beige coloured inner layer, green coloured middle layer and beige coloured outer layer. ‘BOR Plus Monolayer PP-R Pipes (SDR 6 & SDR 7.4)’. Extruded, beige coloured PP-R pipes. For use with water up to 85°C.
'Smart S-IRV'. Site applied, grey coloured, two-part (resin & hardener is automatically mixed in a 10:1 volume ratio through dispensing nozzle) anchor resins. Apply and cure as per ’T Load’ cures set out in Table B3 of European Technical Assessment ‘ETA 14/0141’, dated ‘29/11/2023’. For use with water up to 23°C. If the cure conditions are varied from those specified in ’T Load’ cures set out in set out in Table B3 of European Technical Assessment ‘ETA 14/0104’ then the materials are not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
'Smart S-IRE'. Site applied, light pink coloured, two-part (resin & hardener is automatically mixed in a 3:1 volume ratio through dispensing nozzle) anchor resins. Apply and cure as per ’T Load’ cures set out in Table B3 of European Technical Assessment ‘ETA 17/0187’, dated ‘29/11/2023’. For use with water up to 65°C. If the cure conditions are varied from those specified in ’T Load’ cures set out in set out in Table B3 of European Technical Assessment ‘ETA 16/0884’ then the materials are not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
‘Sika AnchorFix®-3030'. Site applied, grey coloured, two-part (resin & hardener is automatically mixed in a 3:1 volume ratio through dispensing nozzle) anchor resins. Apply and cure as per ’T Load’ cures set out in Table B4 of European Technical Assessment ‘ETA 17/0694’, dated ‘09/09/2025’. For use with water up to 65°C. If the cure conditions are varied from those specified in ’T Load’ cures set out in set out in Table B4 of European Technical Assessment ‘ETA 17/0694’ then the materials are not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
‘Sika AnchorFix®-2+’. Site applied, grey coloured, two-part (resin & hardener is automatically mixed in a 10:1 volume ratio through dispensing nozzle) anchor resin. Apply and cure as per ’T Load’ cures set out in Table B4 of European Technical Assessment ‘ETA 14/0346’, dated ‘07/11/2025’. For use with water up to 23°C. If the cure conditions are varied from those specified in ’T Load’ cures set out in set out in Table B4 of European Technical Assessment ‘ETA 14/0346’ then the materials are not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
Page 639 of 653
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
