'Revolve N-525 Boat Blue M2-018D'. Blue coloured polyethylene material manufactured by rotational moulding. For use with water up to 85°C.
'Klimapress Fitting'. Black coloured, injection moulded PPSU fitting. For use with water up to 85°C.
'ROMAKLIMA Pipe'. Extruded, triple layered pipe comprising of a green coloured PP-R inner layer, green coloured PP-R (with glass fibre) middle layer and green coloured PP-R outer layer (with dark green stripes). For use with water up to 85°C.
'Romafaser CT pipe'. Extruded, triple layered pipe comprising of a green coloured PP-RCT inner layer, green coloured PP-RCT (with glass fibre) middle layer and green coloured PP-RCT outer layer. For use with water up to 85°C.
`PPR 001` Pipes. White (with red external stripe) or tangerine coloured, extruded polypropylene pipes. For use with water up to 85°C.
'Q-Therm'. Extruded, multi-layered PP-R CT pipe comprising of a green coloured PPR inner layer, translucent PPR/glass fibre middle layer and green coloured PPR outer later. For use with water up to 85°C.
'+GF+ Aquasystem PP-RCT'. Extruded, green coloured (with yellow external stripe), multi-layered pipe. All three layers of the pipe are green coloured and made from PP-RCT but the middle layer also has glass fibres. For use with water up to 85°C.
'F420B00 natural (appears off-white), F420B99 (black coloured) & F410K01 (white coloured)'. Injection moulded, glass filled polypropylene materials. For use with water up to 85°C.
'Xytrex 115'. Black coloured, hot compression moulded PTFE washer. For use with water up to 85°C.
'Xytrex 120'. Black coloured, hot compression moulded PTFE washer. For use with water up to 85°C.
`FORWA PTFE tape`. White coloured, extruded PTFE tape. For use with water up to 85°C.
'Hepworth CPVC Pipe'. Grey coloured, extruded CPVC pipe. For use with water up to 85°C.
'Art. 0985077205 Anti-leak Tape'. Site applied, off-white coloured, fibre glass impregnated, polyurethane repair tape. Apply as per manufacturer's technical data sheet version '001' dated 26.07.2021. Cure for 30 minutes@23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Intercrete 4800'. Site applied, grey coloured cementitious repair mortar. Mix Intercrete 4800 and water in a mass ratio of 7.58:1. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Chemfix 10'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated '12/11/2020'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chemfix 600'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated '11/11/2020'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EP7008S 'O' rings and gaskets'. Black coloured, compression moulded EPDM 'O' rings and gaskets. Shore hardness 70. Tested in-radius size between 0.25mm & 3.5mm. For use with water up to 60°C.
'EP1/1/6 BLK' O-rings. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 80. Tested in-radius size 1.75mm. For use with water up to 85°C.
'EP906'. Black coloured, extruded EPDM washer. Shore hardness 90. Tested in-radius size 1.4mm. For use with water up to 85°C.
'ERIKS 55985 Gaskets & ‘O’ rings'. Black coloured, compression moulded EPDM gaskets & ‘O’ rings'. Shore hardness 70A. The gaskets have a tested in-radius size of 1.0mm. The ‘O’ rings have a tested in-radius size of 1.76mm. For use with water up to 85°C.
Page 55 of 394
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
