Silver and copper disinfection ion generator with a plastic body, incorporating a plastic flow switch. Maximum working pressure 9.0 bar. For cold water use only

Section:

2415 Water conditioners - Disinfectant ion generators

WRAS Approval Number:

2107067

Note:

This product actively uses copper for microorganism control purposes. These are subject to the EU Biocidal Products Regulation EU 528/2012. The EU Commissions’ decision of 13 February and 26 June 2014 granted the UK limited essential use derogations only for the control of legionella and limits the range of applications where this product can be used. Users should ensure these types of products are used in accordance with the authorisations issued by the HSE. Users should refer to the HSE website to keep themselves up to date on progress or for further information – www.hse.org.uk/ legionnaires/faqs.htm

Size:

22mm spigot inlet & 22mm push fit outlet.

Marking:

ProEconomy Limited and Ray on adhesive label on body

Installation Requirements:

R001 R150 R170 R290 R415

Expiry date:

31/07/2026

Model:

Ray unit

Product Images

Approval Holder:

ProEconomy Ltd.

Company Name

ProEconomy Ltd.

Address

23 Beaufort Court, Roebuck Way, Knowlhill, Milton Keynes

Postcode

MK5 8HL

View All Listings by this Company

Manufacturer:

ProEconomy Ltd.

Company Name

ProEconomy Ltd.

Address

23 Beaufort Court, Roebuck Way, Knowlhill, Milton Keynes

Postcode

MK5 8HL

View All Listings by this Company

Range of domestic, salt regenerated ion exchange water softeners. Maximum working pressure 6.0 bar. Cold water use only.

Section:

2450 Water softeners

Size:

¾” BSP (M) inlet/outlet.

Marking:

Monarch Company details, Plumbsoft, model, product info on label on rear on body Plumsoft on front of body

Installation Requirements:

R001 R150 R170 R290 R415

Expiry date:

31/10/2026

Proviso:

Discharge to drain must be via a type `AA`, `AB` or `AD` air gap in accordance with EN1717.

Model:

Ultra HE, Ultra HE28, Duo HE, LPS10 HE, PROBOS10 HE, EVERBOS10 HE, AQUABOS10 HE, Premio HE, Premio HE28, Duo Plus HE, LPS20 HE, PROBOS20 HE, EVERBOS20 HE & AQUABOS20 HE WATER SOFTENERS

Product Images

Approval Holder:

Monarch Water Ltd

Company Name

Monarch Water Ltd

Address

Fair Green Diss Norfolk

Postcode

IP22 4DG

Country

United Kingdom

Phone

01986 784759

General Email

kdelaney@monarchwater.co.uk

View All Listings by this Company

'Delrin®RAFG100 NC010'. White coloured (opaque), injection moulded acetal material. For use with water up to 85°C.

Section:

5015 Acetal

Section Subtitle:

Material only. Components made from materials listed in this section may be required to be submitted for audit tests.

WRAS Approval Number:

2009558

Expiry date:

30/09/2025

Approval Holder:

Delrin Switzerland Sàrl

Company Name

Delrin Switzerland Sàrl

Address

154-156 route du Nant d’Avril, CH-1217 Meyrin

Country

Switzerland

View All Listings by this Company

‘Inertol BS10’. Factory applied, black coloured bitumen coating. Apply as per manufacturer’s technical data sheet 'no. 786.3' dated 2013-V2'. Cure for 5 hours@23°C or 30 minutes@50°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval. Petroleum or asphaltic bitumen, NOT coal tar bitumen. Materials listed in this section are not approved for use for contact with water that is required to be wholesome on large water retaining structures such as lining of pipes, cisterns or water storage tanks.

Section:

5021 Bituminous Based Products

Section Subtitle:

Petroleum or asphaltic bitumen, NOT coal tar bitumen. Materials containing petroleum or asphaltic bitumen are not approved for use on water-retaining structures with large surface:volume ratio such as lining of pipes, cisterns or water storage tanks in contact with wholesome water, but may be acceptable for use where there is only a small surface area in contact with the water – e.g. taps, valves and pipe connectors.

WRAS Approval Number:

2202503

Expiry date:

28/02/2027

Approval Holder:

Mäder Group

Company Name

Mäder Group

Address

Burschgrundstrasse 10-12, 45894 Gelsenkirchen

Country

Germany

View All Listings by this Company

'CY25C & MAT4000'. Grey coloured, phenolic impregnated carbon washers. For use with water up to 85°C.

Section:

5022 Carbon

Expiry date:

31/01/2026

Approval Holder:

Morgan Advanced Materials

Company Name

Morgan Advanced Materials

Address

1 Rue des Trois Cantons, 8399 Windhof

Country

Luxembourg

View All Listings by this Company