‘SIGMAPRIME 200’ (yellow/Green) Primer for use with ‘SIGMAGUARD CSF 650’ (green) Coating. Factory applied, teal green coloured (once applied), two-component epoxy coating system (manufactured by PPG SSC Co., Ltd. in Ulsan, South Korea). Mix parts A & B of ‘SIGMAPRIME 200’ (yellow/Green) Primer in an 80:20 volume ratio and apply as per manufacturer’s Product Data Sheet ‘Ref. 7416’, dated ‘June 06 2025 (Revision of May 01 2025)’. Cure for 24 hours@20°C. Mix parts A & B of ‘SIGMAGUARD CSF 650’ (green) Coating in an 80:20 volume ratio and apply as per manufacturer’s Product Data Sheet ‘Ref. 7443’, dated ‘March 18 2025 (Revision of December 13 2024)’. Cure for 5 days@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘SIGMAPRIME 700 HSV’ (yellow/Green) Primer for use with ‘SIGMAGUARD CSF 650’ (green) Coating. Factory applied, teal green coloured (once applied), two-component epoxy coating system (manufactured by PPG Coatings (Kunshan) Co., Ltd. in Kunshan, China). Mix parts A & B of ‘SIGMAPRIME 700 HSV’ (yellow/Green) Primer in an 80:20 volume ratio and apply as per manufacturer’s Product Data Sheet ‘Ref. P757’, dated ‘February 20 2025 (Revision of February 10 2025)’. Cure for 24 hours@20°C. Mix parts A & B of ‘SIGMAGUARD CSF 650’ (green) Coating in an 80:20 volume ratio and apply as per manufacturer’s Product Data Sheet ‘Ref. 7443’, dated ‘March 18 2025 (Revision of December 13 2024)’. Cure for 5 days@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘SIGMAPRIME 200’ (yellow/Green) Primer for use with ‘SIGMAGUARD CSF 650’ (green) Coating. Factory applied, teal green coloured (once applied), two-component epoxy coating system (manufactured by PPG Coatings (Kunshan) Co., Ltd. in Kunshan, China). Mix parts A & B of ‘SIGMAPRIME 200’ (yellow/Green) Primer in an 80:20 volume ratio and apply as per manufacturer’s Product Data Sheet ‘Ref. 7416’, dated ‘June 06 2025 (Revision of May 01 2025)’. Cure for 24 hours@20°C. Mix parts A & B of ‘SIGMAGUARD CSF 650’ (green) Coating in an 80:20 volume ratio and apply as per manufacturer’s Product Data Sheet ‘Ref. 7443’, dated ‘March 18 2025 (Revision of December 13 2024)’. Cure for 5 days@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LOCTITE® EA 3478™'. Factory applied, dark grey coloured, two-component epoxy coating. Mix parts A & B in a 7.25:1 weight ratio and apply as per manufacturer's Technical Data Sheet dated 'November 2016'. Cure for 24 hours@22°C. For use with water up to 23°C. his material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotapipe AC 1003 Green'. Factory applied, green coloured Fusion Bonded Epoxy coating. Apply as per manufacturer's TDS issued '25 May 2022'. Cure for 110 seconds@232°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EM6/35/7541/1 Vitrecoat'. Factory applied, dark blue coloured Porcelain (vitreous) enamel coating. Apply as per manufacturer's instructions 'IS_003', 'rev. 01'. Cure for 16 min 875°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'IF1947T'. Factory applied, red coloured Fusion Bonded Epoxy coating. Apply as per manufacturer's Instructions for Use 'Doc. No. SPPR/L3/WI/PRD/28.' Cure for 45 minutes@220°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Eco Coat FBE Red RAL 3013' (red coloured) & 'Eco Coat FBE Blue RAL 5017' (blue coloured). Factory applied Epoxy coatings. Apply as per manufacturer's Instructions for Use 'Doc. No.:SPPR/L3/WI/PRD/28A'. Cure for 45 minutes@220°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'YT-001'. Single layer, extruded, natural (appears white) PEX hose. For use with water up to 85°C.
'F15222 Center & PHCB042 Center'. Off-white coloured (opaque) silicone greases. Apply as per manufacturer's instructions. For use with water up to 65°C.
‘Silicone Grease A665016, 665016-TUB, A665017, ASG50, AHPSG50, PH041, PHCB041/F15220 & PHCB042/F15222’. Off-white coloured (opaque) silicone greases. Apply as per manufacturer's instructions. For use with water up to 65°C.
'SAF SUDAIR PE-100 Pipes'. Black coloured (blue external stripe), extruded PE-100 pipes. For use with water up to 85°C.
'A001 Series PEX-AL-PEX Pipe'. Extruded pipe with a white coloured inner layer, aluminium middle layer and white coloured outer layer. For use with water up to 75°C.
'Hepworth PE 80 & PE 100 Pipes'. The extruded PE 80 pipes are black coloured. The extruded PE 100 pipes are either black or blue coloured. For use with water up to 60°C.
'SAUDI HEPCO PE-100 HDPE PIPES'. Black coloured (with blue external stripe), extruded PE-100 pipes. For use with water up to 65°C.
'Jingyu PE100 pipe'. Black coloured (with blue stripe), extruded PE100 pipe. For use with water up to 23°C.
'Jingyu PE100 fittings'. Black coloured, injection moulded PE100 fittings. For use with water up to 23°C.
'PPE HY3140GYellow' & 'PPE HY3140GBlack'. Yellow or black coloured, injection moulded PPE materials. For use with water up to 85°C.
‘AquaFlex T 5818’. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.1mm. For use with water up to 23°C.
'PSX 34 Epoxy adhesive'. Site applied, two-part Epoxy adhesive/sealant comprising of a black coloured paste and grey coloured paste, supplied as a pre-weighed kit. Mix, apply and cure as per manufacturer’s TDS ‘ADH4710ENG_PotableWater Feb 2026’. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 506 of 522
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
