'Radius Systems Puriton Dark Blue Barrier Pipe [Type A, BS8588]'. Extruded, multi-layered pipe comprising of a black coloured PE100 inner layer, aluminium middle later and dark blue coloured PE100 outer layer. For use with water up to 23°C.
'LARTON G/40 NAT.:0169F1'. Brown coloured, injection moulded PPS material. For use with water up to 85°C.
'BLAZE PPR01'. Green coloured (with red external stripe), extruded polypropylene pipe. For use with water up to 85°C.
'Tecoflex TU40 GR30 GR128 HS D6 QF'. Light grey coloured, injection moulded TPU material. For use with water up to 23°C.
'Sylwrap LH'. Light green coloured, resin impregnated fibreglass repair fabric. Apply as per manufacturer's instructions label on packaging. Cure for 10 minutes@22°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'DS MAX'. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resin. Apply as per manufacturer's instructions 'Version 28', dated 03.04.2025. Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘NS’. Site applied, grey coloured chemical anchor resin which is supplied in a pre-mixed cartridge. Apply as per manufacturer’s instructions 'Version 23.04.2025'. Cure for 4 days@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EP60PF - EP80PF 'O' rings, gaskets & seals'. Black coloured, compression moulded EPDM 'O' rings, gaskets & seals. Shore hardness between 60 & 80. Tested in-radius size between 0.75mm & 2.66m. For use with water up to 85°C.
'GJ-yzxj-V40 EPDM valve seat'. Black coloured, compression moulded EPDM valve seat. Shore hardness 70. Tested in-radius size 3.5mm. For use with water up to 85°C.
'51M5536'. Black coloured, injection moulded EPDM material. Shore hardness 55 ShA. Tested in-radius size 0.5mm. For use with water up to 23°C.
'WRC-70 'O' rings and gaskets'. Black coloured, injection moulded NBR rubber 'O' rings and gaskets. Tested in-radius size between 0.5mm & 2.6mm. Shore hardness 70. For use with water up to 23°C.
'VL1001P279'. Blue coloured, compression moulded silicone rubber. Shore hardness 60. Tested in-radius size 0.99mm. For use with water up to 65°C.
'CarboStop 102/CarboStop 102 ACC'. Site applied, cream coloured (once applied) waterstop. Mix CarboStop 102 resin and CarboStop 102 ACC accelerator in a weight ratio of 20:0.4. Apply and cure as per manufacturer's Application Guide, revision date '19/09/25'. For use with water up to 23°C. This material is for use in concrete reservoirs and similar structures, constructed in accordance with the design criteria of BS EN 1992 with respect to normal frequency of joints. The material has been tested at a reduced surface area to volume ratio of 1000mm² per litre as specified in BS 6920: Part 1. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Ultra Thread Polyamide Sealing Cord'. White coloured (opaque) thread sealing cord. Apply as per manufacturer's TDS '0800-CORD-150', issue '2', dated 'Aug 2025'. For use with water up to 85°C.
'Loxeal UVAE 83-50 HT Fluo'. Green coloured anaerobic adhesive. For use with water up to 85°C. These products are to be applied and cured in strict accordance with the manufacturer's instructions.
'Weld-On 319 PVC Cement'. Clear Solvent Cement. Apply as per manufacturer's TDS '319-05-2024'. Cure for 4 hours@5°C. For use with water up to 23°C.
'Aliaxis Solvent Cement'. Clear, transparent (un-pigmented) solvent cement, (intended to join PVC pipe and fittings). Apply as per manufacturer's instructions 'Rev00 08052025'. Cure for 20 days at 7°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EcoFITTOM Fittings'. Blue coloured PVC fittings which are manufactured by extrusion and molecular orientation. For use with water up to 60°C.
'TOM PVC-O Pipe'. Blue coloured PVC pipe which is manufactured by extrusion and molecular orientation. For use with water up to 60°C.
Concealed WC dual flushing cisterns with a vertical BS 1212-4(2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two-push button assembly. The product also incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10 Bar, cold water use only.
Page 506 of 590
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
