Pumps

Section Code 1610 : Wholesome water use.

Back To Directory Sections

#2105321

‘Showermate Universal’ range of booster pumps with plastic bodies and impellers, stainless steel shafts, brass manifolds, NBR ‘O’-rings and EPDM seals. The product incorporates a pressure vessel. The outlet(s) incorporate(s) an approved single check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection The inlet hose(s) supplied with this product incorporate(s) an isolation valve. Maximum working pressure 4.0 bar. Maximum operating temperature 65°C.

Section:
1610 Pumps
Section Subtitle:
Wholesome water use.
WRAS Approval Number:
2105321
Note:
IRN R150 applies to both inlets of the Twin models only.
Size:
Stainless-steel braided EPDM lined flexible hoses with 15mm pushfit (inlet and outlets) x ¾” BSP captive nut end connections (to pump).
Marking:
Stuart Turner, model name, part no., serial number including date of manufacture (YYWW000-000, where 000-000 changes numerically to denote serial number) & other technical information on adhesive label on pump body. Showermate on pump body.
Installation Requirements:
R001 R150 R415
Expiry date:
31/05/2026
Model:
47375: Showermate U2.6 bar Single. 47376: Showermate U2.0 bar Twin. 47377: Showermate U2.6 bar Twin. 44921: Showermate U2.6 bar Single. 44918: Showermate U2.0 bar Twin. 44922: Showermate U2.6 bar Twin.
Approval Holder:
Stuart Turner Ltd
Company Name
Stuart Turner Ltd
Address
47 Market Place Henley-on-Thames Oxfordshire
Postcode
RG9 2AD
Country
United Kingdom
Phone
01491 572655
General Email
stuart.savill@stuart-turner.co.uk

View All Listings by this Company

Print This Approval

#2111366

Range of cold water in tank booster sets incorporating an ‘AG’ air gap, consisting of a GRP water storage cistern incorporating a float operated inlet valve, with a copper float and submersible pump or pumps (depending on model). The products incorporate an externally mounted stainless-steel manifold with servicing valve(s), expansion vessel, pressure gauge and a digital control panel. The pumps are connected to the external components via a discharge assembly of internal pipework including an in-line non-verifiable single check valve assembly (suitable for backflow prevention of Fluid Category 2). Maximum working pressure 10.0 bar. Cold water use only.

Section:
1610 Pumps
Section Subtitle:
Wholesome water use.
WRAS Approval Number:
2111366
Note:
These cisterns are not suitable for water for domestic purposes unless they are so modified and installed as to comply in all respects with Schedule 2. Section 7, Paragraph 4, of the Water Supply (Water Fittings) Regulations 1999. The products incorporate a Fluid Category 3 air gap arrangement.
Size:
1" BSP (M)
Marking:
Fluid Water, Stuart Turner or Flowtech, address, product ref, capacity, job ref and contact information on adhesive label on tank body. Fluid Water or Stuart Turner, model, year of manufacturer and serial no on control box.
Installation Requirements:
R001 R280 R415
Expiry date:
30/11/2026
Proviso:
If implemented, the overflow and warning pipe discharge to drain must be via a type `AA` `AB` or `AD` airgap in accordance with EN 1717.
Model:
IT-A-V-B-C-D-E-F-G-AG Where: IT = Product range name (In Tank). A = Number of pumps (1,2, or 3 pumps). V = Variable speed. B = Maximum flow (l/min per pump - 80 or 120l/min). C = Maximum head (m per Pump, e.g. 60). D = Controller type (MAB). E = Power input (T = 3 Phase – M = 1Phase). F = Vessel Capacity (8 = 8 litre, 24= 24 litre). G = Tank size (Nominal capacity in litres - 250-3000). AG = ‘AG’ air gap. Example: IT-3V-8060-MAB-M/24-1000-AG In Tank booster set with 3 pumps, variable speed, 80l/min max. flow and 60m max. head, MAB controller, 1 phase, 24 litre expansion vessel, 1000 litre capacity with an AG air gap. Model added October 2025: IN - A - B - C - D - E - F IN = Product range name A = number of pumps (1,2, or 3 pumps) B = Maximum flow (per pump) C = Maximum Head (per pump) D = Tank capacity E = Voltage F = Controller Type Example: IN3-8060-1000-M-MAB • IN = product range • A = 3 pumps • B = 80 l/min max flow • C = 60m max head • D = 1000L nominal capacity • E – 1 phase 230v • F = MAB control panel
Approval Holder:
Dutypoint Ltd.
Company Name
Dutypoint Ltd.
Address
Unit A, Quedgeley West Business Park, Hardwicke, Gloucester
Postcode
GL2 4PA
Country
United Kingdom
Phone
01452313334
General Email
austin.hill@dutypoint.com

View All Listings by this Company

Print This Approval

#2111367

Range of cold water in tank booster sets incorporating an ‘AB’ air gap, consisting of a GRP water storage cistern incorporating a float operated inlet valve, with a copper float and submersible pump or pumps (depending on model). The products incorporate an externally mounted stainless-steel manifold with servicing valve(s), expansion vessel, pressure gauge and a digital control panel. The pumps are connected to the external components via a discharge assembly of internal pipework including an in-line non-verifiable single check valve assembly (suitable for backflow prevention of Fluid Category 2). Maximum working pressure 10.0 bar. Cold water use only.

Section:
1610 Pumps
Section Subtitle:
Wholesome water use.
WRAS Approval Number:
2111367
Note:
These cisterns are not suitable for water for domestic purposes unless they are so modified and installed as to comply in all respects with Schedule 2. Section 7, Paragraph 4, of the Water Supply (Water Fittings) Regulations 1999. The products incorporate a Fluid Category 5 air gap arrangement.
Size:
1" BSP (M)
Marking:
Fluid Water or Stuart Turner, address, product ref, capacity, job ref and contact information on adhesive label on tank body. Fluid Water or Stuart Turner, model, year of manufacturer and serial no on control box.
Installation Requirements:
R001 R280 R415
Expiry date:
30/11/2026
Proviso:
If implemented, the warning pipe discharge to drain must be via a type `AA` `AB` or `AD` airgap in accordance with EN 1717.
Model:
IT-A-V-B-C-D-E-F-G-AB Where: IT = Product range name (In Tank). A = Number of pumps (1,2, or 3 pumps). V = Variable speed. B = Maximum flow (l/min per pump - 80 or 120l/min). C = Maximum head (m per Pump, e.g. 60). D = Controller type (MAB). E = Power input (T = 3 Phase – M = 1Phase). F = Vessel Capacity (8 = 8 litre, 24= 24 litre). G = Tank size (Nominal capacity in litres - 250-3000). AB = ‘AB’ air gap. Example: IT-3V-8060-MAB-M/24-1000-AB In Tank booster set with 3 pumps, variable speed, 80l/min max. flow and 60m max. head, MAB controller, 1 phase, 24 litre expansion vessel, 1000 litre capacity with an AB air gap.
Approval Holder:
Stuart Turner Ltd
Company Name
Stuart Turner Ltd
Address
47 Market Place Henley-on-Thames Oxfordshire
Postcode
RG9 2AD
Country
United Kingdom
Phone
01491 572655
General Email
stuart.savill@stuart-turner.co.uk

View All Listings by this Company

Print This Approval

#2112057

Range of pumps with stainless steel bodies and plastic impellors. Maximum working pressure 16.0 bar. Maximum operating temperature 95°C.

Section:
1610 Pumps
Section Subtitle:
Wholesome water use.
WRAS Approval Number:
2112057
Size:
1½” BSP (M) or 2” (M) inlet/outlet.
Marking:
Wilo SE, model and product info on data plate on body
Installation Requirements:
R001 R415
Expiry date:
31/12/2026
Model:
Para MAXO-Z 25-180-08. Para MAXO-Z 25-180-10. Para MAXO-Z 30-180-08. Para MAXO-Z 30-180-10.
Approval Holder:
Wilo SE
Company Name
Wilo SE
Address
Werk Hof, Heimgartenstr. 1-3, 95030 Hof/Saale
Country
Germany

View All Listings by this Company

Print This Approval

#2201059

‘EVE Whole house’ twin impeller booster pump with a plastic body and impellers and EPDM ‘O’-rings. The inlet and outlet hoses incorporate a screwdriver operated isolation valve. The pump body outlets incorporate a non-return valve. The product is supplied with two loose combined EPDM and stainless steel inlet washers and two loose EPDM outlet washers. Maximum working pressure 3.0 bar. Maximum operating temperature 65°C.

Section:
1610 Pumps
Section Subtitle:
Wholesome water use.
WRAS Approval Number:
2201059
Size:
Quadruple layered flexible hose consisting of a black coloured TPE inner layer, PVC middle layer, braided PE third layer and grey outer layer with 22mm pushfit end connections.
Marking:
Salamander logo on top cover. Salamander logo, maximum temperature, maximum pressure, and product info on adhesive label on lid. Flow arrow on body.
Installation Requirements:
R001 R150 R415
Expiry date:
31/01/2027
Model:
EVE Whole House Booster Pump: EVETU (twin variant).
Approval Holder:
Salamander Pumps
Company Name
Salamander Pumps
Postcode
SR5 3XE
Country
United Kingdom
Phone
0191 535 4528
General Email
lewisw@salamanderpumps.co.uk

View All Listings by this Company
Manufacturer:
Salamander Pumps
Company Name
Salamander Pumps
Postcode
SR5 3XE
Country
United Kingdom
Phone
0191 535 4528
General Email
lewisw@salamanderpumps.co.uk

View All Listings by this Company

Print This Approval


Show Per Page
5102050Show All

Back To Directory Sections

Page 6 of 36

© WRAS 2026 | Update Cookie Consent

Site Developed By Duo

We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.