| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| M5005 X XXX | VARIOUS | 3/4" BSP | 10.0 bar | 65 °C | PPI | REAR OF BODY | No | 1/4 Turn ceramic disk | Metal Backnuts | Open Outlet | Shower Hose, Handset, |
X XXX Denotes the following: First X: Different handle and the second, third & fourth XXX for different finishes: Handles: A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Range of wall mounted, two-hole, single outlet (fixed) bath/shower mixers, (brass bodies – various finishes). Incorporating a thermostatic cartridge controlling the temperature and a manual diverter controlling the flow between the outlets with dome type operating members. The spout outlet incorporates a plastic aerator. Both inlets incorporate stainless steel strainers and approved check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Two hole, single outlet (swivel) combination tap assembly with brass bodies (chrome plated), incorporating quarter turn ceramic disc headworks and single lever operating members. The spout outlet incorporates a plastic aerator or plastic flow straightener. The product is supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of three-hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes). The products Incorporate either a non-rising spindle (model 1641 only) or quarter turn ceramic disc headworks (all other models) with either cross top (model 1641 only) or single lever (all other models) operating members. The spout outlet incorporates a plastic aerator. The products are supplied with a a pop-up waste not verified by test. Maximum working pressure 3.0 Bar Maximum operating temperature 65.0°C
Range of three-hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes). The products incorporate either a non-rising spindle (model 1851 only) or quarter turn ceramic disc (model 1850 only) headworks with either cross top (model 1851 only) or single lever (model 1850 only) operating members. The spout outlet incorporates a plastic aerator. The products are supplied with metal backnuts and lever operated pop-up wastes. Maximum working pressure 3.0 Bar Maximum operating temperature 65.0°C
Range of wall mounted bath spout outlets incorporating (brass bodies - various finishes) with a plastic aerator. The product can also be supplied with a pop-up waste – not verified by test (see models). Maximum working pressure 6.0 Bar Maximum operating temperature 65.0°C
Range of Chlorine Dioxide dosing systems supplied with a stub flange and tee fitting. Maximum operating pressure 15.0 bar. Cold water use only.
Range of water filters with a plastic body and plastic filter. The products are supplied with a spherical valve, which acts as a drain valve. This is provided loose for the installer to attach, or for models added July 2025 it can also be factory applied. Maximum working pressure 6.0 bar. Cold water use only.
Range of filter shower handsets and tap outlets with plastic bodies with EPDM O-Rings Open Outlet use. Maximum operating temperature 60°C
‘GM50xx’ range of stainless steel (SS304 or SS316L) press-fit fittings incorporating EPDM ‘O’-rings for use with *- STPT304 and *- STPT316 stainless steel pipes. The GM5004 prefix models also incorporates an EPDM gasket on the union nut. Jointing is achieved via a crimping tool using a ‘M’ profile. For above and below ground use. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of stainless-steel press fittings with EPDM ‘O’-rings for use with stainless-steel pipe to EN10312. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
Range of solder ring copper fittings for use with copper tube to EN 1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Solder ring brass fittings for use with copper tube (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
‘EPH_WSP19_XXXX’ range of brass caplillary, lead free solder ring and threaded fittings for use with copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
‘Flowflex,’ and ‘Opal’ ranges of brass, DZR brass, chromium plated brass, nickel plated brass compression fittings for use with copper pipe to BS EN 1057. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
CORE “SB DZRCOM” range of DZR brass compression fittings for use with copper pipe (manufactured to EN 1057). The tank connectors incorporate a NBR gasket. The straight tap connectors incorporate a blue fibre gasket. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
‘Instantor Lead-Free Brass’ compression fittings with DZR brass body, for use with DZR Copper tube (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Twistloc’ range of push-fit fittings with PEX-b, polysulphone or PPE bodies, supplied with polysulphone inserts. For use with PEX pipe (manufactured to BSEN 7291 part 3), PB (manufactured to BSEN 7291 part 2) and copper pipe. Maximum working pressure 12.5 bar. Cold water use only.
‘HDE-210xxx-xx’ range of brass press-fit fittings incorporating EPDM ‘O’-rings for use with copper pipes (manufactured to EN1057). Jointing is achieved via a crimping tool using a ‘M’ profile. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of copper or brass (see model) end feed fittings for use with copper tube (manufactured to BS EN1057). Tap connectors incorporate Fibre/NBR washers. Male and female union adaptors incorporate a silicone gasket. Maximum working pressure using hard solder: 8mm to 28mm, ½” to 1” BSP (F) or (M), 1” straight cylinder union and captive nut ½” to ¾”: 25.0 bar, 35mm to 54mm, 1¼” to 2” BSP (F) or (M): 16.0 bar. Maximum working pressure using silver brazing alloy EN1044: 66.7mm to 108mm, 2½” to 4” BSP (F) or (M): 16.0 bar, 133mm to 219mm: 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Page 464 of 506
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
