'MS519'. Factory applied, blue coloured Porcelain Enamel coating. Apply as per manufacturer's instructions dated 2021.6.23. Dry for 2 hours@100°C before firing for 10 minutes@860°C For use with water up to 75°C. This material is only approved for the drying and firing conditions that appear on the approval. If the drying and/or firing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'GMF-01'. Factory applied, grey coloured cement mortar. Mix sand, water & cement in a 1.5:1.0:1.0 weight ratio. Cure for 24 hours@25°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EARTHSTAHL TYPE OPC'. Factory applied, grey coloured cement mortar. Mix cement, sand & water in a 1.0:1.5:0.5. Cure for 28 days@26°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EARTHSTAHL TYPE SRC'. Factory applied, grey coloured cement mortar. Mix cement, sand & water in a 1.0:1.5:0.5. Cure for 28 days@26°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EARTHSTAHL TYPE BFSC'. Factory applied, grey coloured cement mortar. Mix cement, sand & water in a 1.0:1.5:0.5. Cure for 28 days@26°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Norsodyne H 13212 TAE Laminate' for use with 'Polycor White Gel Coat'. ‘NORSODYNE H 13212 BTAE Laminate' was added to the approval in July 2024. The glass fibre panel is manufactured by hand lay method and then factory applied, unsaturated resin gel coat is applied by brush (BR) or spray (PA). The brush gel coat is to be applied as per manufacturer's TDS ‘4100’ dated 10.10.17 and cured for 24 hours@25°C. The spray gel coat is to be applied as per manufacturer's TDS ‘4200’ dated 10.10.17 and cured for 24 hours@25°C. For use with water up to 23°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'HEXELL SC 3093 TYPE BLACK G01'. Black coloured, rotmoulded LLDPE material. For use with water up to 23°C.
'HEXELL SC 3093 TYPE GREY B22 MIX B11'. Grey coloured, rotmoulded LLDPE material. For use with water up to 23°C.
'TASNEE 100 Black'. Black coloured HDPE material manufactured in Saudi Arabia and Germany, for injection moulding and extrusion purposes. For use with water up to 60°C.
'Aidmer78-031'. White coloured (opaque), extruded PTFE pipe. For use with water up to 85°C.
'AQUAPEA® In-line Repair'. Site applied, dark grey coloured (once mixed), two-part epoxy putty (light grey and dark grey coloured) and polypropylene core (white, translucent). Mix & cure as per the document: “Aquapea method statement issue 1 dated 23-04-21” . For use with water up to 23°C.
'4273 'O' rings and washers'. Black coloured, injection moulded EPDM 'O' rings and washers. Shore hardness 70. The 'O' rings have an in-radius size of 1.31mm. The washers have an in-radius size of 2.00mm. For use with water up to 85°C.
'EP10/00/2 BLK EPDM 'O' rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 65. Tested in-radius size 1.5mm. For use with water up to 85°C.
'HYPRESS12V'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.1mm. Between June 2021 and August 2022, the material was for use with water up to 23°C. Between September 2022 and June 2026, the material is for use with water up to 65°C.
'S/EP-50, S/EP-60, S/EP-70 & S/EP-80'. Black coloured, compression moulded EPDM materials with a shore hardness of between 50A & 80A. Tested in-radius size 1.05mm. For use with water up to 65°C.
'ILPEA 70-90 EPDM COMPOUND WRAS AF'. Black coloured, compression moulded EPDM material. Shore hardness 80. Tested in-radius size 1.25mm. For use with water up to 23°C.
'EPDM-W E267'. Black coloured, compression moulded EPDM material. Shore hardness 80A. Tested in-radius size 1.0mm. For use with water up to 85°C.
'Hongli IRHD50'. Black coloured, press moulded EPDM material. Shore hardness 50. Tested in-radius size 1.12mm. For use with water up to 50°C.
'A-KT 70-00'. Black coloured, extruded and rotocured EPDM rubber material. Shore hardness 70. Tested in-radius size 1.00mm. For use with water up to 23°C.
'Sunaflex T 8289'. Black coloured, compression moulded EPDM rubber material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 23°C.
Page 46 of 521
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
