Range of screw down valves with brass or DZR brass bodies, brass or DZR brass bonnets, EPDM washers and PTFE seats. Compression connection to be used with copper pipe manufactured to EN1057. Maximum working pressure 16 bar. Maximum operating temperature 85°C.
Ultra violet disinfection units consisting of a stainless steel body and quartz sleeve. Model WS-10-1206/3030031 Alde Aquaclear has a maximum working pressure of 5.0 bar and a maximum operating temperature of 40°C. All other models have a maximum working pressure of 7.0 bar and a maximum operating temperature of 60°C.
'SPL Gold Sulphate Resisting Portland Cement'. Factory applied, grey coloured Sulphate Resisting Portland Cement. Mix cement, sand and water in a 1.0:1.4:0.35 mass ratio and apply as per manufacturer's work instructions document code 'WI/SP/FINC&B/02', issue '06'. Cure for 24 hours at 27°C & 70% RH. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Endoprene 888.55'. Factory applied, two-component, beige coloured polyurethane coating. Mix and apply as per manufacturer's Data Sheet 'Doc. 089' dated '01/07/2011'. Cure for 8 days@20°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Art-Coat'. Factory applied, colourless (transparent) PTFE based surface treatment coating. Apply as per manufacturer's instructions 'revision 3' dated 16-03-2020. Cure for 45 minutes@55-60°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'OP-90601' (orange coloured) & 'IP-90604' (light orange coloured). Injection moulded polyester materials. For use with water up to 50°C.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. Models are either cold/premixed water only or hot and cold supply with a manually adjustable temperature lever. The product incorporates stainless steel strainers and the inlets incorporate approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 70°C.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated brass). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The spout outlet incorporates a plastic aerator and the inlets incorporates stainless steel strainers. Models 351500 & 351510 incorporate an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Models are either cold/premixed water only or hot and cold supply with a manually adjustable temperature lever. Maximum working pressure 8.0 bar. Maximum operating temperature 70°C.
‘Tubular’ range of wall mounted spout outlets (chromium plated brass). The flow is controlled by a solenoid valve activated via an infra-red sensor. The box assembly incorporates a solenoid valve, screwdriver operated spherical valve and the spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.
A range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve activated via an infra-red sensor. The temperature is controlled independently via a dome operating member. The spout outlet incorporates a plastic aerator. The inlets incorporate stainless steel strainers and single check valve cartridges (however, the complete assembly has not been fully tested to demonstrate that it provides adequate backflow protection). Maximum working pressure 5.0 Bar Maximum operating temperature 65 °C
Page 425 of 1134
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
