Range of gate valves incorporating blue epoxy coated ductile iron bodies, EPDM coated wedges. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
Range of non-rising spindle gate valves with bronze, brass or DZR brass bodies, incorporating hand wheel or key operated operating members. Maximum working pressure 16.0 Bar GVBZ25 Series = 25.0 bar Maximum working temperature: 85C
Non-metallic materials and components comply with BS6920 at 85°C
Range of hand wheel operated gate valves with blue epoxy coated ductile iron bodies, ductile iron wedge encapsulated in EPDM. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C
Range of gate valves incorporating either rising or non-rising spindle headworks and PTFE gaskets. The products are available as follows: Bronze body, bronze wedge and handwheel (GVBZR20, GVBZ20 and GVBZ prefix models). Bronze body, bronze wedge and lockshield (GVBZLS16 and GVBZLS20 prefix models). Brass body, brass wedge and handwheel (GVBZ16 model only). Maximum working pressure 20.0 bar & 25.0 bar (model GVBZLS16 DN50 only). Maximum operating temperature 85°C.
Range of gate valves with bronze bodies, bronze wedge and PTFE gaskets. The valves incorporate a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of screw down stop valves with brass bodies, incorporating EPDM gaskets. Compression connection to be used with copper pipe EN1057. Maximum working pressure 16 Bar. Maximum operating temperature 85°C.
Range of screw down stop valves with brass or chrome plated brass bodies and EPDM seals. For use with copper pipe to EN1057. Maximum working pressure 16.0 Bar Maximum operating temperature 85 °C.
Range of screw down stop valves with plastic bodies, NBR washers and ‘O’ rings. For use with polyethylene pipe (manufactured to EN 12201). For above and below ground use. Maximum working pressure 6 bar. Cold water use only.
Range of regulating balancing valves with blue epoxy coated ductile iron bodies incorporating EPDM gaskets and hand wheel operating member. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
'WITCOAT HIGH BUILD BITUMINOUS BLACK PAINT'. Factory applied, black coloured bitumen paint. Apply as per manufacturer's TDS, dated '28.06.2025'. Cure for 72 hours@30°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PENTALINE DI 750 BLUE'. Factory applied, two-part, blue coloured epoxy coating. Mix parts A and B in a 3:1 volume ratio and apply as per manufacturer's TDS 'Issue date: August 2023. Reference No - 01'. Cure for 7 days@30°C. For use with water up to 65°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'GM2025-01'. Factory applied, grey coloured sulphate resistant cement. Mix cement:sand:water in a 1.5:1:0.4 mass ratio. Cure for 8 hours@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Factory applied, two-part, black or white polyurethane coatings. 'Pentathane 1000 SD Black'. Mix parts A & B in a 2.5:1 volume ratio and apply as per ‘August 2022’. Cure for 7 days@25°C. For use with water up to 65°C. 'Pentathane 1000 SD Off White'. Mix parts A & B in a 3:1 volume ratio and apply as per ‘August 2022’. Cure for 7 days@25°C. For use with water up to 23°C.
'Abcite® 1060 DW Blue & Abcite® X60 DW Blue'. Factory applied, blue coloured thermoplastic powder coatings applied by dipping in a fluidised bed. Pre-heat substrate the coating is to be applied to for 12 minutes@280°C and apply as per manufacturer’s Application Guide ‘Version 04.05.2015’ (Abcite® 1060 DW Blue) or Technical Data Sheet ‘11/2023’ (Abcite® X60 DW Blue). Post-heat for 5 minutes@160°C. For use with water up to 23°C. These materials are only approved for the pre-heat and post-heat conditions that appear on the approval. If the pre-heat and/or post-heat conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'MC-PROOF 4200 AE'. Site applied, cream coloured (once mixed), two-component urethane based coating. Mix Part A (amber liquid) with Part B (amber liquid) in a volume ratio of 1:1 and apply as per manufacturer's TDS dated 07.10.2025. Cure for 24 hours@7°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MC-PROOF 4210 AE'. Site applied, grey coloured (once mixed), two-component polyol and prepolymer based coating. Mix Part A (grey liquid) with Part B (amber liquid) in a volume ratio of 1:1 and apply as per manufacturer's TDS '07.10.2025'. Cure for 24 hours@7°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Lewatit S 1568 & Lewatit S 1567'. Amber coloured, translucent ion exchange resins. For use with water up to 23°C.
'ZGC110DQ & ZGC108DQ'. Beige coloured ion exchange resins. For use with water up to 65°C.
'WL1225 Lubricant Soft Soap'. Amber coloured (translucent) lubricant. Apply as per manufacturer's IFU dated 22nd April 2025. For use with water up to 65°C. This material incorporates a natural ingredient. Please note that water companies will evaluate the evidence provided and may ask for more information and they reserve the right to refuse installation.
'RP380s & RP361'. Off-white coloured (opaque) silicone greases. Apply as per manufacturer's instructions. For use with water up to 65°C.
Page 403 of 443
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
