‘Renderoc ST 05’. Site applied, light grey coloured, two part cement based mortar consisting of a liquid (white coloured) and a powder (grey coloured paste). Mix and apply as per manufacturer`s instructions 'ST/June 2022'. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5038 Coatings, Paints & Linings

Section Subtitle:

Site applied concrete coatings. Compliance with BS6920 relates to the conditions of cure specified in the listing. If the cure conditions are varied from those described below then compliance with BS6920 cannot be assummed without further testing. Where catalysts are required, only tested catalysts in the recommended concentrations should be used. Manufacturer's advice must be sought if any non standard mixing or curing conditions are being considered.

WRAS Approval Number:

2302502

Expiry date:

29/02/2028

Approval Holder:

Saint-Gobain Construction Chemicals UK Limited

Company Name

Saint-Gobain Construction Chemicals UK Limited

Address

Saint-Gobain House, East Leake, Loughborough, Leicestershire

Postcode

LE12 6JU

View All Listings by this Company

'Eurokote 480 FC'. Site applied, red coloured (once mixed), two part epoxy coating consisting of a resin and hardener. Mix, apply and cure (fully dry) in accordance with manufacturer's technical data sheet dated 23/09/2021. For use with water up to 23°C.

Section:

5042 Coatings, Paints & Linings

Section Subtitle:

Site applied pipe and fittings coatings. Compliance with BS6920 relates to the conditions of cure specified in the listing. If the cure conditions are varied from those described below then compliance with BS6920 cannot be assummed without further testing. Where catalysts are required, only tested catalysts in the recommended concentrations should be used. Manufacturer's advice must be sought if any non standard mixing or curing conditions are being considered.

WRAS Approval Number:

2208524

Expiry date:

31/08/2027

Approval Holder:

BS Coatings

Company Name

BS Coatings

Address

Allee Paul Sabatier, BP 88, 27940 Aubevoye

Country

France

Phone

+ 33 32773077

View All Listings by this Company

‘Polycor LP Gel Coat reinforced with Norsodyne H 13212 TAE laminating resin’. ‘NORSODYNE H 13212 BTAE laminating resin’ was added to the approval in July 2024. ‘Polycor LP Gel Coat’ is a brush or spray applied polyester resin gel coat, available in white or grey colours and is reinforced with Norsodyne H 13212 TAE or NORSODYNE H 13212 BTAE glass fibre laminate. Apply the brush grade as per manufacturer’s technical data sheet ‘7100’ dated 10.10.17 and apply the spray grade as per manufacturer’s technical data sheet ‘7200’ also dated 10.10.17. Cure for 24 hours@25°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5125 Glass Reinforced Plastics (GRP)

Section Subtitle:

Material only. Components made from materials listed in this section may be required to be submitted for audit tests.

WRAS Approval Number:

2208543

Expiry date:

31/08/2027

Approval Holder:

Polynt Composites UK limited

Company Name

Polynt Composites UK limited

Address

Laporte Road, Stallingborough, Nr. Grimsby, Lincolnshire

Postcode

DN41 8DR

Phone

+44 1469 572464

View All Listings by this Company

'Eltex Superstress TUB121N6000'. Black coloured, extruded polyethylene material. For use with water up to 23°C.

Section:

5245 Polyethylene

Section Subtitle:

Material only. Components made from materials listed in this section may be required to be submitted for audit tests.

WRAS Approval Number:

2209523

Expiry date:

30/09/2027

Approval Holder:

INEOS Olefins and Polymers Europe

Company Name

INEOS Olefins and Polymers Europe

Address

Ransbeekstraat 310, B-1120 Brussels

Country

Belgium

View All Listings by this Company

'Eltex TUB121'. Black coloured, extruded polyethylene material. For use with water up to 60°C.

Section:

5245 Polyethylene

Section Subtitle:

Material only. Components made from materials listed in this section may be required to be submitted for audit tests.

WRAS Approval Number:

2209524

Expiry date:

30/09/2027

Approval Holder:

INEOS Olefins and Polymers Europe

Company Name

INEOS Olefins and Polymers Europe

Address

Ransbeekstraat 310, B-1120 Brussels

Country

Belgium

View All Listings by this Company