'EPDM-LJHY'. Black coloured, compression moulded EPDM materials. Shore hardness between 50 & 75. Tested in-radius size 1.0mm. For use with water up to 85°C.
'AN004LFG'. Black coloured, compression moulded Ebonite rubber material. Shore hardness 75. Tested in-radius size 2.6mm. For use with water up to 23°C.
'SIL7018 red & SIL7018 blue'. Red and blue coloured, compression moulded silicone rubber 'O' rings. Shore hardness 70A. Tested in-radius size 2.6mm. For use with water up to 85°C.
‘7400, 7500, 7600, 7700 & 7800 ‘O’ rings’. Red coloured, compression moulded silicone rubber `O` rings. Shore hardness between 40 & 80. Tested in-radii sizes between 0.5mm & 2.0mm. ‘7700 washers’. Red coloured, compression moulded, silicone rubber rectangular washers. Shore hardness 70. Tested in-radius size 1.33mm. ‘7700 PLC091130 Profile Packing Seal’. Red coloured, compression moulded silicone rubber seal. Shore hardness 70. Tested in-radius size 2.26mm. All for use with water up to 85°C.
'SYC3 0825 S30CB04 Boot'. Black coloured, compression moulded silicone rubber boot component. Shore hardness 30. The component has an irregular shape with a tested in-radius size of between 0.6mm & 1.2mm. For use with water up to 85°C.
'ADDISIL IND. 60 E’. Natural (appears white), injection moulded silicone rubber material. Shore hardness 60. Tested in-radius size 1.25mm. For use with water up to 85°C.
'LOXEAL 55-03'. Blue coloured anaerobic adhesive. For use with water up to 85°C. These products are to be applied and cured in strict accordance with the manufacturer's instructions.
MXLOC acrylic based adhesives. Apply as per manufacturer`s instructions. Grades for use with water up to 23°C. MXLOC 22 (purple coloured), 11243, 70, & 90 (green coloured). MXLOC 42 & 43 (blue coloured). MXLOC 542 (brown coloured). MXLOC 12638, 38 & 48 (green coloured). MXLOC 71 & MXBON 11271 (red coloured). Grade for use with water up to 85°C. MXLOC 13577, 577 & MXBON 13577 (yellow coloured).
'GIRPI HTA Fusion'. Site applied, orange coloured solvent cement, intended to join plastic pipe and fittings. Apply as per manufacturer instructions '6311289/20'. Cure for 24 hours@7°C. For use with water up to 70°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'‘Welding polymer for Kryoclim®️, Girair®️ and HTA (formerly known as GIRPI HTA Fusion THF Free'. Site applied, orange coloured solvent cement, intended to join PVC-C pipe and fittings. Apply as per pages 4.2 & 4.3 of 'Durapipe HTA®' technical data sheet '04900200 February 2013'. Cure for 24 hours at 7°C. For use with water up to 70°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ACRYSTEX® PM-600'. Transparent, injection moulded Methyl Methacrylate-Styrene Copolymer (MS or SMMA) material. For use with water up to 85°C.
Floor mounted, single hole, single outlet (fixed) combination tap assembly (brass bodies - in various finishes), incorporating a ceramic cartridge headwork with a single lever operating member, a manual diverter to shower outlet and a waterfall type spout. Shower hose and handset is not supplied with this product. Maximum working pressure 10.0bar. Maximum operating temperature 60°C.
'BUTYL B Membrane'. Black coloured, compression moulded Butyl membrane. Shore hardness 55. Tested in-radius size 1.0mm. For use with water up to 85°C.
Range of wall mounted, electronically operated combination tap assembly (chrome plated brass body). The flow is controlled by a solenoid valve which is actuated via an infrared sensor. The spout outlets incorporate a plastic aerator. The solenoid valve inlet incorporates a plastic and stainless steel filter. The products are supplied with a triple layered connecting hose (PVC inner and outer layer and nylon braided middle layer). Maximum working pressure 8.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Deck mounted single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve actuated via an infra-red sensor. Temperature is manually blended using a single lever operating member. The spout outlets incorporate plastic aerators. The inlets incorporate approved check valve cartridges, however, the complete assembly has not been fully tested to demonstrate that it provides backflow protection and stainless-steel strainers. Maximum operating pressure 8.0 bar. Maximum operating temperature 65°C.
Range of concealed WC dual flushing cisterns with a vertical BS 1212-4(2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two-push button assembly. The product also incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10 Bar, cold water use only.
Three-hole, single outlet (fixed), combination tap assembly (brass body – various finishes), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to the shower outlet. The product is supplied with a stainless-steel braided EPDM lined flexible connection hose to connect the head work to the spout outlet. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
In-line non-verifiable single check valve assembly consisting of a single check valve cartridge housed within a DZR brass body. Maximum working pressure 16.0 bar. Cold water use only.
Verifiable double check valve assembly consisting of two spring loaded resilient trim in-line check valve cartridges housed in a DZR brass body with two test ports. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Single hole, single outlet (fixed) over the rim swivel nozzle bidet combination tap assembly (brass body - various finishes) with a ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a plastic flow straightener. The product is supplied with a lever operated pop-up waste (not verified by test). Maximum working pressure 5.0 Bar. Maximum operating temperature 60.0°C.
Page 398 of 566
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
