‘Aquastrom’ range of regulating valves with brass bodies. Maximum working pressure 16.0 Bar Maximum operating temperature 90.0°C
Range of in-line scale inhibitors with stainless steel bodies. Maximum working pressure 10.0 bar. Cold water use only.
Range of in-line water conditioners with stainless steel bodies and catalytic alloy core. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of inline water conditioners with stainless steel bodies and catalytic alloy core. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of ultraviolet disinfection units with stainless-steel bodies. Maximum working pressure 16.0 bar. Cold water use only.
'VSS1'. Dark grey coloured, sintered silicon carbide washer. For use with water up to 85°C.
'Series 2000 RAL 5015'. Factory applied, blue coloured epoxy resin coating. Apply as per manufacturer’s data application sheet ‘Revision: 6 (2018/10/01)’ created ‘2015/11/11’. Cure for 10 minutes@180°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CLEAN TECH PW (BG)'. Factory applied, two-component, blue coloured epoxy coating. Mix parts A and B in a volume ratio of 3:1 and apply as per manufacturer's TDS 'CCPL/TDS/R11/CRC/22-23/04/R13/BG/R1', dated '15.09.2022'. Cure for 7 days@30°C. Between August 2024 and January 2025, the coating is approved for use with water up to 23°C. Between February 2025 and August 2029, the coating is approved for use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Advashield PW'. Factory applied, grey coloured epoxy coating. Apply as per manufacturer's TDS issued 1st September 2024. Cure for 7 days@25°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MJ-6'. Factory applied, blue coloured epoxy resin powder coating. Mix in a 63%/21.8%/13.2%/2% ratio and apply as per manufacturers instructions 'v1', dated '06-05-2023'. Cure for 60 minutes@200°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘NMSP2104 M & ER2104A01SM'. The following coatings were added to the approval in March 2025: ER2209A01SC, ER2252A01SC, ER2259A01SC & ER2260A01SC. Factory applied, blue coloured, porcelain (vitreous) enamel coatings. Apply as per manufacturer’s user manual 'PEM 38', edition '01' dated '14/10/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘PMSP5099-M & EP5099D01SC'. Factory applied, blue coloured, porcelain (vitreous) enamel coatings. Apply as per manufacturer’s user manual 'PEM 37', edition '01' dated '14/10/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PRIMGREEN® ENDURANCE & Primgreen LAT 12035' primers for use with 'RILSAN® PA11 T BLUE 7444 MAC (16293), PA11 T GREY 5161 MAC (17203), PA11 T WHITE 1488 AC (17219) & PA11 T BLACK 7450 AC (17185)' coatings. Factory applied primers and powder coatings. The piece to be coated is to be pre-heated to 330°C for 10 minutes, the primer and coating applied in accordance with user instructions 'Dircom - 4418E/05.2015/20' and then cured for 10 minutes@330°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘FlatSeal™HMF10’. Orange coloured NBR/aramid fibre gasket material, manufactured by calendaring. For use with water up to 85°C. For use only as a gasket material having been tested at a reduced surface area to volume ratio.
FORTRON® natural (appears cream) or black coloured, injection moulded PPS materials. For use with water up to 85°C. Grades manufactured in Celanese Florence, USA: FORTRON® 1140L4 SF3001 NATURAL FORTRON® 1140L4 SD3002 BLACK DW (formerly known as FORTRON® 1140L4 BLACK SD3002). FORTRON® 1140L6 SD3002 BLACK DW (formerly known as FORTRON® 1140L6 BLACK SD3002). FORTRON® 1140L6 SF3001 NATURAL FORTRON® 4184L6 SF3001 NATURAL FORTRON® 4184L6 SD3002 BLACK DW (formerly known as FORTRON® 4184L6 BLACK SD3002). Grades manufactured in Celanese Nanjing: FORTRON® 1140L4 SF3001 NATURAL DW (formerly known as FORTRON® 1140 L4 SF3001 natur CN). FORTRON® 1140L4 SD3002 BLACK DW (formerly known as FORTRON® 1140 L4 SD 3002 black).
'LCKB70'. Black coloured, compression moulded EPDM material. Shore hardness 70A. Tested in-radius size 1.3mm. For use with water up to 85°C.
'E13970'. Black coloured, injection moulded EPDM material. Shore hardness 65. Tested in-radius size 1.3mm. For use with water up to 23°C.
'NB01280PWRC'. Black coloured, compression moulded NBR rubber material. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 85°C.
'NE7130 Grey 60'. Light grey coloured, injection moulded silicone rubber material. Shore hardness 60. Tested in-radius size 1.97mm. For use with water up to 85°C.
'Ultra Tight Thread Sealing Cord'. White coloured (opaque) sealing cord. Apply as per manufacturer's TDS 'V1.0'. For use with water up to 85°C.
Page 372 of 505
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
