'Interline 925P Light Grey & Interline 925P Off White'. Site applied, two component epoxy coatings. Mix Parts A & B in a volume ratio of 3:1 and apply as per manufacturer's datasheet '10257', issue date '07/02/2022'. Cure for 7 days@25°C. For use with water up to 60°C. These materials are only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.

Section:

5042 Coatings, Paints & Linings

Section Subtitle:

Site applied pipe and fittings coatings. Compliance with BS6920 relates to the conditions of cure specified in the listing. If the cure conditions are varied from those described below then compliance with BS6920 cannot be assummed without further testing. Where catalysts are required, only tested catalysts in the recommended concentrations should be used. Manufacturer's advice must be sought if any non standard mixing or curing conditions are being considered.

WRAS Approval Number:

2304554

Expiry date:

30/04/2028

Approval Holder:

Akzo Nobel Saudi Arabia Ltd.

Company Name

Akzo Nobel Saudi Arabia Ltd.

Country

Saudi Arabia

View All Listings by this Company

‘MoyaProof WS2’. Site applied, grey coloured (once mixed), two-component, polymer modified Portland cement based cementitious waterproofing membrane. Mix Part A (white, opaque liquid) with Part B (grey, opaque powder) in a 1:4 mass ratio and apply two coats as per manufacturer’s Technical Datasheet ‘CC/MP05/Ver09/01/21’. Cure Coat 1 for 2 hours at 5˚C. Cure Coat 2 for 28 days at 5˚C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5055 Concrete, Cement and Mortar

Section Subtitle:

Waterproofers.

WRAS Approval Number:

2308508

Expiry date:

31/08/2028

Approval Holder:

Conmix Limited

Company Name

Conmix Limited

Address

City Gate Tower, Al Tawun, PO Box 5936, Sharjah

Country

United Arab Emirates

View All Listings by this Company

'Rotormagnet 12-0000294'. Dark grey coloured, injection moulded Polyamide + Strontium Ferrite magnet. For use with water up to 60°C.

Section:

5165 Magnetic Material

Expiry date:

31/05/2028

Approval Holder:

MS Schramberg GmbH

Company Name

MS Schramberg GmbH

Address

Max-Planck-Str. 15, 78713 Schramberg

Country

Germany

View All Listings by this Company

'15.0903.01 & 15.0902.01'. Dark grey coloured, ferrite anisotropic magnets (commonly known as ceramic magnets). For use with water up to 85°C.

Section:

5165 Magnetic Material

Expiry date:

31/05/2029

Approval Holder:

Eltek SpA

Company Name

Eltek SpA

Address

Strada Valenza 5/A Casale Monferrato

Postcode

15033

Country

Italy

Phone

+39 0142 335511

General Email

f.ruzzafante@eltekgroup.it

View All Listings by this Company

'ForTii Ace WX51-FC BK00001, ForTii PA Xgea20 BK28049 & PA Xgea BK28049'. Black coloured, injection moulded PA 4T materials. For use with water up to 85°C.

Section:

5180 Nylon

Section Subtitle:

Material only. Components made from materials listed in this section may be required to be submitted for audit tests.

WRAS Approval Number:

2307519

Expiry date:

31/07/2028

Approval Holder:

Envalior

Company Name

Envalior

Address

Flughafenstrasse 101, 40474 Dusseldorf

Country

Germany

View All Listings by this Company