Range of flow switches with brass bodies incorporating EPDM ‘O’-rings, acting as a leak detection system that actuates an integral spherical valve to shut off the water supply. The inlet incorporates a stainless steel strainer. The outlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 16.0 bar. Maximum operating temperature 30°C.

Section:

1719 Flow Activated Switches

WRAS Approval Number:

2012087

Note:

Cannot be used as the main stop valve into a premises. The fitting listed on this approval has been judged only against the requirements of The Water Supply (Water Fittings) Regulations 1999 (England and Wales), The Water Supply (Water Fittings) (Scotland) Byelaws 2014 or The Water Supply (Water Fittings) Regulations (Northern Ireland) 2009. The decision of the Scheme to list them is not to be taken as any guide as to their effectiveness to do the job for which they have been designed.

Size:

¾”, 1” & 1¼” BSP (M) inlet/outlet.

Marking:

RELIANCE VALVES ON PLASTIC COVER

Installation Requirements:

R001

Expiry date:

31/12/2025

Model:

LEKP100001 - ¾, LEKP100002 1” & LEKP100003 1¼ FLOW ACTIVATED SWITCHES

Product Images

Manufacturer:

Reliance Worldwide Corporation

Company Name

Reliance Worldwide Corporation

Address

Horton Road, West Drayton

Postcode

UB7 8JL

Country

United Kingdom

Phone

+44 7730 052060

View All Listings by this Company

Range of pillar taps incorporating either stainless steel or brass bodies (various finishes), quarter turn ceramic disc headworks with a single lever operating member. The spout outlet incorporates a plastic aerator. The RB3 models are supplied with a pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.

Section:

1800 Taps

Section Subtitle:

Pillar tap(s).

WRAS Approval Number:

2111007

Note:

No testing performed on pop-up waste.

Size:

Stainless steel braided PEX lined flexible hose assembly incorporating a 10mm spigot end connection.

Marking:

Vola on operating member

Installation Requirements:

R001 R006 R009

Expiry date:

30/11/2026

Model:

VOLA RB1-XX Stainless steel. VOLA RB3-XX Stainless steel. Where XX denotes the surface finish: 40 = Stainless Steel, 61 = Brushed Black, 64 = Brushed Copper, 70 = Brushed Gold, 71 = Brushed Dark Copper. VOLA RB1-XX Brass. VOLA RB3-XX Brass. Where XX denotes the surface finish: 02 = Grey, 04 = Blue, 05 = Orange, 06 = Light Green, 08 = Yellow, 09 = Dark Grey, 12 = Mocca, 14 = Bright Red, 15 = Dark Blue, 16 = Chrome, 17 = Gloss Black, 18 = White, 19 = Natural Brass, 20 = Brushed Chrome, 21 = Carmine Red, 25 = Pink, 27 = Matt Black, 28 = Matt White, 60 = Black, B61 = Brushed Black, 62 = Deep Black, 63 = Copper, B64 = Brushed Copper, 65 = Gold, 66 = Dark Gold, 68 = Nickel, B70 = Brushed Gold.

Approval Holder:

Vola A/S

Company Name

Vola A/S

Address

Lunavej 2 Horsens

Postcode

8700

Country

Denmark

Phone

+4576284846

General Email

mk@vola.dk

View All Listings by this Company

Manufacturer:

Vola A/S

Company Name

Vola A/S

Address

Lunavej 2 Horsens

Postcode

8700

Country

Denmark

Phone

+4576284846

General Email

mk@vola.dk

View All Listings by this Company

Range of chromium plated brass interlocked shower hoses incorporating either a PVC or TPE inner hose and EPDM gaskets. Maximum operating temperature 60°C.

Section:

1860 Tubes

Section Subtitle:

Plastic hoses.

WRAS Approval Number:

2106045

Note:

Open outlet use only.

Size:

½” BSP Captive nut inlet x outlet.

Marking:

WRAS, DTC15 and date of manufacture YY ON CONICAL NUT

Installation Requirements:

R001

Expiry date:

30/06/2026

Model:

HOS1.5CPS01, HOS1.5CPS01/G & D50010014 SHOWER HOSES

Product Images

Approval Holder:

Methven UK Limited

Company Name

Methven UK Limited

Address

3-3A Stone Cross Court Yew Tree Way Golborne Warrington

Postcode

WA3 3JE

Country

United Kingdom

Phone

0800 195 1602

General Email

raluca.olariu@uk.methven.com

View All Listings by this Company

PEX lined flexible hose assemblies with either nylon or stainless-steel braiding and a variety of end connectors. Some models are supplied with screwdriver operated isolation valves. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.

Section:

1860 Tubes

Section Subtitle:

Plastic hoses.

WRAS Approval Number:

2204701

Size:

See model

Marking:

HRN’, ‘WRAS’ and manufacturing date (YY/MM) on ferrule.

Installation Requirements:

R001 R008

Expiry date:

30/04/2027

Model:

Bore diameter: DN8, DN10 or DN13 End connections: ½” BSP F, 3/8” BSP F, ¾” BSP F, ½” BSP M, 3/8” BSP M & ¾” BSP M. M8, M10, M12 & M15. 10mm compression, 12mm compression, 15mm compression & 22mm compression. 15mm compression isolation valve & 22mm compression isolation valve. 3-WAY connector x 9mm Quick connector 9mm M-Quick plastic connector, 9mm M-quick Brass connector 135-A-B-C-D-E-F. The letters denote the following (for DN8): A and B denotes length and is replaced by 02 (90mm) up to 83 (2519mm). C denotes the code for the finish and is replaced by 02 = Grey, 04 = Black, 26 = SUS (Stainless Steel), 36 = Red and 37 = Blue. D denotes the inlet connection and is replaced by 01 = ½” F, 02 = 3/8” F, 03 = ¾” F, 17 = ½” M, 18 = 3/8” M, 19 = 3/4” M, 25 = M8, 27 = M10, 28 = M12, 29 = M15, 39 = 10mm compression, 40 = 12mm compression, 41 = 15mm compression, 42 = 22mm compression, 46 = 1/4" M, 47 = M14, 48 = M16, 49 = 3/8" F Elbow, 50 = 1/2 F Elbow, 51 = 3/4 F Elbow, 52 = 3-way connector, 53 = F-quick connective, 54 = M-quick plastic connective, 55 = M-quick brass connective. E denotes the outlet connection and is replaced by 01 = ½” F, 02 = 3/8” F, 03 = ¾” F, 17 = ½” M, 18 = 3/8” M, 19 = 3/4” M, 25 = M8, 27 = M10, 28 = M12, 29 = M15, 39 = 10mm compression, 40 = 12mm compression, 41 = 15mm compression, 42 = 22mm compression, 46 = 1/4" M, 47 = M14, 48 = M16, 49 = 3/8" F Elbow, 50 = 1/2 F Elbow, 51 = 3/4 F Elbow, 52 = 3-way connector, 53 = F-quick connective, 54 = M-quick plastic connective, 55 = M-quick brass connective F denotes DN size and is replaced by: 0 = DN8. The letters denote the following (for DN10) A and B denotes length and is replaced by 02 (90mm) up to 83 (2519mm). C denotes the code for the finish and is replaced by 02 = Grey, 04 = Black, 26 = SUS (Stainless Steel), 36 = Red and 37 = Blue. D denotes the inlet connection and is replaced by 01 = ½” F, 02 = 3/8” F, 03 = ¾” F, 17 = ½” M, 18 = 3/8” M, 19 = 3/4” M, 25 = M8, 27 = M10, 28 = M12, 29 = M15, 39 = 10mm compression, 40 = 12mm compression, 41 = 15mm compression, 42 = 22mm compression, 44 = 15mm compression isolation valve and 45 = 22mm compression isolation valve, 46 = 1/4" M, 47 = M14, 48 = M16, 49 = 3/8" F elbow, 50 = 1/2" F elbow, 51 = 3/4" F elbow E denotes the outlet connection and is replaced by 01 = ½” F, 02 = 3/8” F, 03 = ¾” F, 17 = ½” M, 18 = 3/8” M, 19 = 3/4” M, 25 = M8, 27 = M10, 28 = M12, 29 = M15, 39 = 10mm compression, 40 = 12mm compression, 41 = 15mm compression, 42 = 22mm compression, 44 = 15mm compression isolation valve and 45 = 22mm compression isolation valve, 46 = 1/4" M, 47 = M14, 48 = M16, 49 = 3/8" F elbow, 50 = 1/2" F elbow, 51 = 3/4" F elbow. F denotes DN size and is replaced by: 2 = DN10 The letters denote the following (for DN13) A and B denotes length and is replaced by 02 (90mm) up to 83 (2519mm). C denotes the code for the finish and is replaced by 02 = Grey, 04 = Black, 26 = SUS (Stainless Steel), 36 = Red and 37 = Blue. D denotes the inlet connection and is replaced by 01 = ½” F, 03 = ¾” F, 17 = ½” M, 19 = 3/4” M, 29 = M15, 39 = 10mm compression, 40 = 12mm compression, 41 = 15mm compression, 42 = 22mm compression, 44 = 15mm compression isolation valve and 45 = 22mm compression isolation valve, 46 = 1/4" M, 48 = M16, 50 = 1/2" F elbow, 51 = 3/4" F elbow E denotes the outlet connection and is replaced by 01 = ½” F, 02 = 3/8” F, 03 = ¾” F, 17 = ½” M, 18 = 3/8” M, 19 = 3/4” M, 25 = M8, 27 = M10, 28 = M12, 29 = M15, 39 = 10mm compression, 40 = 12mm compression, 41 = 15mm compression, 42 = 22mm compression, 44 = 15mm compression isolation valve and 45 = 22mm compression isolation valve, 46 = 1/4" M, 47 = M14, 48 = M16, 49 = 3/8" F elbow, 50 = 1/2" F elbow, 51 = 3/4" F elbow. F denotes DN size and is replaced by: 2 = DN13

Approval Holder:

APIS (Xiamen) Co., Ltd.

Company Name

APIS (Xiamen) Co., Ltd.

Address

1F, 5F, Main building No 198-204 YingYao Road

Country

Jimei District

View All Listings by this Company

Manufacturer:

APIS (Xiamen) Co., Ltd.

Company Name

APIS (Xiamen) Co., Ltd.

Address

1F, 5F, Main building No 198-204 YingYao Road

Country

Jimei District

View All Listings by this Company

EPDM lined flexible hose assemblies with either nylon or stainless-steel braiding and a variety of end connectors. Some models are supplied with screwdriver operated isolation valves. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.

Section:

1863 Tubes

Section Subtitle:

Elastomeric.

WRAS Approval Number:

2204700

Size:

See model

Marking:

HRN’, ‘WRAS’ and date of manufacture (YY/MM) on ferrule.

Installation Requirements:

R001

Expiry date:

30/04/2027

Model:

Bore diameter: DN8, DN10 or DN13 End connections: ½” BSP F, 3/8” BSP F, ¾” BSP F, ½” BSP M, 3/8” BSP M & ¾” BSP M. M8, M10, M12 & M15. 10mm compression, 12mm compression, 15mm compression & 22mm compression. 3-WAY connector x 9mm Quick connector 9mm M-Quick plastic connector, 9mm M-quick Brass connector 134-A-B-C-D-E-F. The letters denote the following (for DN8): A and B denotes length and is replaced by 02 (90mm) up to 83 (2519mm). C denotes the code for the finish and is replaced by 02 = Grey, 04 = Black, 26 = SUS (Stainless Steel), 36 = Red and 37 = Blue. D denotes the inlet connection and is replaced by 01 = ½” F, 02 = 3/8” F, 03 = ¾” F, 17 = ½” M, 18 = 3/8” M, 19 = 3/4” M, 25 = M8, 27 = M10, 28 = M12, 29 = M15, 39 = 10mm compression, 40 = 12mm compression, 41 = 15mm compression, 42 = 22mm compression, 46 = 1/4" M, 47 = M14, 48 = M16, 49 = 3/8" F Elbow, 50 = 1/2 F Elbow, 51 = 3/4 F Elbow, 52 = 3-way connector, 53 = F-quick connective, 54 = M-quick plastic connective, 55 = M-quick brass connective. E denotes the outlet connection and is replaced by 01 = ½” F, 02 = 3/8” F, 03 = ¾” F, 17 = ½” M, 18 = 3/8” M, 19 = 3/4” M, 25 = M8, 27 = M10, 28 = M12, 29 = M15, 39 = 10mm compression, 40 = 12mm compression, 41 = 15mm compression, 42 = 22mm compression, 46 = 1/4" M, 47 = M14, 48 = M16, 49 = 3/8" F Elbow, 50 = 1/2 F Elbow, 51 = 3/4 F Elbow, 52 = 3-way connector, 53 = F-quick connective, 54 = M-quick plastic connective, 55 = M-quick brass connective F denotes DN size and is replaced by: 0 = DN8. The letters denote the following (for DN10) A and B denotes length and is replaced by 02 (90mm) up to 83 (2519mm). C denotes the code for the finish and is replaced by 02 = Grey, 04 = Black, 26 = SUS (Stainless Steel), 36 = Red and 37 = Blue. D denotes the inlet connection and is replaced by 01 = ½” F, 02 = 3/8” F, 03 = ¾” F, 17 = ½” M, 18 = 3/8” M, 19 = 3/4” M, 25 = M8, 27 = M10, 28 = M12, 29 = M15, 39 = 10mm compression, 40 = 12mm compression, 41 = 15mm compression, 42 = 22mm compression, 44 = 15mm compression isolation valve and 45 = 22mm compression isolation valve, 46 = 1/4" M, 47 = M14, 48 = M16, 49 = 3/8" F elbow, 50 = 1/2" F elbow, 51 = 3/4" F elbow E denotes the outlet connection and is replaced by 01 = ½” F, 02 = 3/8” F, 03 = ¾” F, 17 = ½” M, 18 = 3/8” M, 19 = 3/4” M, 25 = M8, 27 = M10, 28 = M12, 29 = M15, 39 = 10mm compression, 40 = 12mm compression, 41 = 15mm compression, 42 = 22mm compression, 44 = 15mm compression isolation valve and 45 = 22mm compression isolation valve, 46 = 1/4" M, 47 = M14, 48 = M16, 49 = 3/8" F elbow, 50 = 1/2" F elbow, 51 = 3/4" F elbow. F denotes DN size and is replaced by: 2 = DN10 The letters denote the following (for DN13) A and B denotes length and is replaced by 02 (90mm) up to 83 (2519mm). C denotes the code for the finish and is replaced by 02 = Grey, 04 = Black, 26 = SUS (Stainless Steel), 36 = Red and 37 = Blue. D denotes the inlet connection and is replaced by 01 = ½” F, 03 = ¾” F, 17 = ½” M, 19 = 3/4” M, 29 = M15, 39 = 10mm compression, 40 = 12mm compression, 41 = 15mm compression, 42 = 22mm compression, 44 = 15mm compression isolation valve and 45 = 22mm compression isolation valve, 46 = 1/4" M, 48 = M16, 50 = 1/2" F elbow, 51 = 3/4" F elbow E denotes the outlet connection and is replaced by 01 = ½” F, 02 = 3/8” F, 03 = ¾” F, 17 = ½” M, 18 = 3/8” M, 19 = 3/4” M, 25 = M8, 27 = M10, 28 = M12, 29 = M15, 39 = 10mm compression, 40 = 12mm compression, 41 = 15mm compression, 42 = 22mm compression, 44 = 15mm compression isolation valve and 45 = 22mm compression isolation valve, 46 = 1/4" M, 47 = M14, 48 = M16, 49 = 3/8" F elbow, 50 = 1/2" F elbow, 51 = 3/4" F elbow. F denotes DN size and is replaced by: 2 = DN13

Approval Holder:

APIS (Xiamen) Co., Ltd.

Company Name

APIS (Xiamen) Co., Ltd.

Address

1F, 5F, Main building No 198-204 YingYao Road

Country

Jimei District

View All Listings by this Company

Manufacturer:

APIS (Xiamen) Co., Ltd.

Company Name

APIS (Xiamen) Co., Ltd.

Address

1F, 5F, Main building No 198-204 YingYao Road

Country

Jimei District

View All Listings by this Company