'FILPEX PE-Xb Pipes'. Extruded, PE-Xb pipes available in brown, blue and white (with blue stripe) colours. For use with water up to 85°C.
'Rifeng PEX/AL/PEX Pipe'. Triple layered, extruded pipe consisting of an off-white coloured PEX inner, aluminium middle layer and white coloured outer layer. For use with water up to 85°C.
'Rifeng PEX Pipe'. Off-white coloured, extruded PEX pipe. For use with water up to 85°C.
'Bingo HDPE Pipes 01'. Black coloured (with blue, external stripes), extruded HDPE pipe. For use with water up to 85°C.
'Bingo HDPE Fittings 02'. Black coloured, injection moulded HDPE fittings. For use with water up to 85°C.
'Hotace HDPE Black Pipe'. Black coloured (with blue stripes), extruded HDPE pipe. For use with water up to 80°C.
'Fortron ICE 504L SD 3039 black (DW)'. Black coloured, injection moulded PPS material. For use with water up to 85°C.
'Ultrason® P 3010 MR grau 30373'. Grey coloured, injection moulded PPSU material. For use with water up to 85°C.
‘+GF+'. Green coloured, extruded PPR pipe. For use with water up to 85°C.
'Lubricomp CX94108-GYDKNAT'. Dark grey coloured, injection moulded Polystyrene material. For use with water up to 85°C.
'Lubricomp CG006-NA1G003 Black'. Black coloured, injection moulded polystyrene material. For use with water up to 85°C.
'PRO V200'. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resin. Apply as per manufacturer's instructions 'Version 7', dated '18/05/2022'. Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ASIIR60WRC'. Black coloured, mould pressed isobutylene isoprene rubber. Shore hardness 65. Tested in-radius size 1.0mm. For use with water up to 85°C.
'DL8099F Gaskets and 'O' rings'. Black coloured, compression moulded EPDM gaskets and 'O' rings. Shore hardness 70. Gaskets have an in-radius size of 1.5mm. 'O' rings have an in-radius size of 1.45mm. For use with water up to 85°C.
'EJ820 'O' ring'. Black coloured, compression moulded EPDM 'O' ring. Shore hardness 70. Tested in-radius size 1.3mm. For use with water up to 85°C.
'E103 Sealing Ring'. Black coloured, injection moulded EPDM sealing ring. Shore hardness 70. Tested in-radius size 1.5mm. Between April 2025 and August 2025, the ring was for use with water up to 23°C. Between September 2025 and April 2030, the ring is for use with water up to 85°C.
'R210WM'. Black coloured, injection moulded EPDM material. Shore hardness 70. Tested in-radius size 1.2mm. For use with water up to 85°C.
'EPW50, EPW55, EPW60, EPW65, EPW70, EPW75 & EPW80'. Black coloured, injection moulded EPDM material. Shore hardness between 50 & 80. Tested in-radius 2.95mm. For use with water up to 65°C.
'ZXMFJ-50 SEALING'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius 1.25mm. For use with water up to 85°C.
'70EP505p'. Black coloured, compression moulded EPDM material. Shore hardness 72. Tested in-radius size 1.0mm. For use with water up to 85°C.
Page 347 of 391
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
