Range of UV disinfection units with stainless steel bodies and EPDM seals. The UV lamps are housed inside quartz tubes. Maximum working pressure 10.3 bar. Maximum operating temperature 40°C.

Section:

2411 Disinfection Equipment

Size:

Please refer to model.

Marking:

‘LUMINOR BLACKCOMB’ and ‘LUMINOR’ logos, model and technical information on adhesive label on body.

Installation Requirements:

R001 R120 R150 R170 R290

Expiry date:

31/05/2027

Model:

LBx-02X (½” female NPT). LBx-03X & LBx-10X (½” male NPT). LBx-06X (¾” male NPT). LBx-08X, LBx-15X & LBx-20X (1” male NPT). LBHx-05X & LBHx-10X (¾” male NPT). LBHx-15X & LBHx-25X (1” male NPT) LBHx-40X (1½” male NPT inlet and outlet). ‘x’ denotes controller option and can be replaced with: 4 = controller does not support UV sensor, ships with plug as standard. 5 = can accept optional UV sensor, ships with plug as standard. 6 = controller is same as LB5, but the LB6 system ships with UV sensor as standard. ‘X’ denotes power cord and can be replaced with 1, 2, 3 or 4.

Approval Holder:

Luminor Environmental Inc.

Company Name

Luminor Environmental Inc.

Address

80 Southgate Drive, Unit 4, Guelph, ON Guelph

Postcode

N1G 4P5

Country

Canada,

View All Listings by this Company

Manufacturer:

Luminor Environmental Inc.

Company Name

Luminor Environmental Inc.

Address

80 Southgate Drive, Unit 4, Guelph, ON Guelph

Postcode

N1G 4P5

Country

Canada,

View All Listings by this Company

Range of UV disinfection units with stainless steel bodies & quartz tubes. All models incorporate a spherical valve on the drain outlet. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C

Section:

2411 Disinfection Equipment

Size:

1” BSP, 1½” BSP & 2” BSP male inlet and outlet.

Marking:

Hydrotec, model, WRAS and technical information on adhesive label on body.

Installation Requirements:

R001 R150 R170 R511

Expiry date:

31/05/2027

Model:

HydroWELL Compact 1E DN40. HydroWELL Compact 2E DN25. HydroWELL Compact 5E DN40. HydroWELL Compact 7E DN50. HydroWELL Compact 10E DN50.

Approval Holder:

Hydrotec International Water Treatment Limited

Company Name

Hydrotec International Water Treatment Limited

Address

38 Main Street Swords Country Dublin

Country

Ireland

View All Listings by this Company

'SOLID-02'. Factory applied, black coloured, bituminous coating. Apply as per manufacturer's user instructions 'File No.: SOLID-0069, Vison: SLD-03, Date of issue: 2015-01-01'. Cure for 2 hours @60°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5021 Bituminous Based Products

Section Subtitle:

Petroleum or asphaltic bitumen, NOT coal tar bitumen. Materials containing petroleum or asphaltic bitumen are not approved for use on water-retaining structures with large surface:volume ratio such as lining of pipes, cisterns or water storage tanks in contact with wholesome water, but may be acceptable for use where there is only a small surface area in contact with the water – e.g. taps, valves and pipe connectors.

WRAS Approval Number:

2205506

Expiry date:

31/05/2027

Approval Holder:

Shanxi Solid Industrial Co., Ltd.

Company Name

Shanxi Solid Industrial Co., Ltd.

Address

28F, No.8 Changxing South Street, Jinyuan District, Taiyuan, Shanxi

Country

China

View All Listings by this Company

'Eurokote® 47-20 Brun Rouge'. Factory applied, red coloured (once mixed and applied), two-component epoxy coating. Mix resin and hardener in an 80:20 mass ratio and apply as per manufacturer's instructions dated '15/06/2021'. Cure for 7 days@20°C. For use with water up to 60°C. his material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5030 Coatings, Paints & Linings

Section Subtitle:

Factory applied pipe & fittings coatings.

WRAS Approval Number:

2204521

Expiry date:

30/04/2027

Approval Holder:

BS Coatings

Company Name

BS Coatings

Address

Allee Paul Sabatier, BP 88, 27940 Aubevoye

Country

France

Phone

+ 33 32773077

View All Listings by this Company

'E0-850-5210-001'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's instructions 'nr.01, rev.00, issue 01' dated 01/082016. Cure for 30 minutes@210°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5030 Coatings, Paints & Linings

Section Subtitle:

Factory applied pipe & fittings coatings.

WRAS Approval Number:

2204522

Expiry date:

30/04/2027

Approval Holder:

Ziac Trattamenti Metallici SNC Di Giona Mario

Company Name

Ziac Trattamenti Metallici SNC Di Giona Mario

Address

Via Mirandola 37, 37059, S. Maria Di Zevio

Country

VR,

View All Listings by this Company