‘SIGMAPRIME 200 K Grey’ for use with ‘SIGMAGUARD CSF 585 (white)’ or ‘SIGMAGUARD CSF 585 (blue)’. Factory applied, white or blue coloured (once mixed and applied), two-part epoxy coating comprising of Coat 1 and Coat 2. ‘SIGMAPRIME 200 K Grey’ (Coat 1) comprises of a base and hardener to be mixed in a 80:20 volume ratio and applied as PDS ‘7416’, dated February 25, 2021. Cure for 24 hours@23°C. ‘SIGMAGUARD CSF 585 (white)’ or ‘SIGMAGUARD CSF 585 (blue)’ is to be applied as Coat 2 and each comprises of a base and hardener to be mixed in a 77.5:22.5 ratio and applied as PDS ‘7785’, dated August 19, 2022. Cure for 12 days@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LMI Hygienic CML'. Factory applied, grey coloured cement mortar. Mix cement mortar:sand:water in a weight ratio of 36:46:18 and apply as per manufacturer's instructions 'LMICMA012624', dated '1/26/2024'. Cure for 20 hours@40°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Crystic Gelcoat 65PA Gel Coat' for use with 'Crystic 125PA GRP resin'. GRP resin, manufactured by hand lamination, for use with white coloured, factory applied gel coat. Apply as per manufacturer's quick guide 'issue number 1', dated 04/06/2018. Cure for 24 hours@23°C and then 3 hours@80°C. For use with water up to 50°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Binh Minh Plastic's HDPE pipe'. Black coloured (with blue stripe), extruded HDPE pipe. For use with water up to 40°C.
'Binh Minh Plastic's PVC-U pipe’. Grey coloured, extruded PVC-U pipe. For use with water up to 45°C.
‘METOLUX Metoset’. Site applied, grey coloured chemical anchor resin which is supplied in a pre-mixed cartridge. Apply as per manufacturer’s instructions 'version 2', dated 29.10.2023. Cure for 4 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SME001 EPDM'. Black coloured, compression moulded EPDM material. Shore hardness 60. In November 2024 'SME001 EPDM', a compression moulded EPDM rubber with a shore hardness of 75 was added to the approval so that a range with a hardness between 60 & 75 is covered by the approval. Tested in-radius size of 1.0mm and are for use with water up to 65°C.
'HT5557-10'. Black coloured, injection moulded EPDM material. Shore hardness 55. Tested in-radius size 1.0mm. Between January 2024 and March 2024, the material was for use with water up to 50°C. From April 2024 the material is for use with water up to 60°C.
‘Trutite Pipe Sealing Cord’. White coloured nylon cord coated with a silicone paste, intended for use as a thread sealant. The cord is to be applied and tightened in accordance with Data Sheet ‘version 1.3’, dated 12/02/24 and this material is only approved for these conditions. For use with water up to 85°C.
'PVCC125 & PVCC250 PVC Pipe Cement'. Clear, transparent (un-pigmented) solvent cement, (intended to join PVC pipe and fittings). Apply as per manufacturer's instructions 'Rev00 24012024'. Cure for 20 days at 7°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 308 of 652
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
